|
It is currently Fri 22. Nov 2024 9:43:27
|
View unanswered posts | View active topics
| Author |
Message |
|
ZeXx86
|
 Posted: Fri 02. Jan 2015 20:07:39 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Different foam is not needed, only requirement is that the unit should be mounted precisely.
The unit can fly well even without any foam.
If you will not be able to observe any difference then we can be sure it is just something wrong on the helicopter and can be solved.
_________________
Spirit System developer
|
|
| Top |
|
 |
|
Jman841
|
Posted: Fri 02. Jan 2015 20:35:40 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Ok, I'll swap them out tonight. Won't be able to test till next week. I'll let you know once its swapped.
|
|
| Top |
|
|
|
Jman841
|
Posted: Fri 02. Jan 2015 20:47:27 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Since the heli leans about 2.5 degrees forward during initialization, could that be the issue? Is there anyway to program the natural tilt of a heli on its skids into the Spirits rescue calculations?
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Fri 02. Jan 2015 20:50:51 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
This shouldn't be a problem. All my helicopters are tilted even more without any issue.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Jman841
|
Posted: Fri 02. Jan 2015 21:23:04 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Ok, good to know. Thank you
|
|
| Top |
|
|
|
Jman841
|
Posted: Sat 03. Jan 2015 0:04:08 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Ok, I pulled the unit off my G570 and will put it on the logo. What is the best location on the FBL tray for the unit to be mounted? Should it be as close to the main dhaft as possible or does that not matter?
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sat 03. Jan 2015 0:13:37 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
OK. It does not matter where the unit is, it must be only perpendicular to all axes.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Jman841
|
Posted: Sat 03. Jan 2015 0:27:07 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Ok, I'll use the grey 3m stuff this time. I find it sticks better and is stiffer.
|
|
| Top |
|
|
|
Jman841
|
Posted: Sat 03. Jan 2015 0:57:36 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Ok, all set back up. I switched it around so the wires are facing to the main shaft instead this time. It's lined up the best I can get it. You can see the reference line in the picture.
We will see how it goes when I fly next.
I'm assuming I don't have to reset the servo subtrim? Or do I?
I changed all the values that needed to be changed for proper compensation of the unit.
I'm going to leave the unit off the G570 till we test this one, incase that one is defective.
| Attachments: |
image.jpg [ 1.04 MiB | Viewed 1055 times ]
|
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sat 03. Jan 2015 11:07:25 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
If your servos are connected to same positions in the unit then you only have to change Sensor/Gyro compensation direction.
You can also check your piro optimization to be sure all is correct.
_________________
Spirit System developer
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: Bing [Bot] and 6 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
