|
It is currently Sun 24. Nov 2024 15:33:26
|
View unanswered posts | View active topics
| Author |
Message |
|
grant22
|
 Posted: Wed 25. Nov 2020 20:09:12 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
I have a Spirit which will not enter Bind mode.
I have a proper connection to the software (3.2 on software and firmware), I have started the Wizard and selected 'dsmx,' I have disconnected the usb cable, put a bind plug in ele/pit/ail, and repowered, and the sat will not rapid flash.
Any ideas?
|
|
| Top |
|
 |
|
ZeXx86
|
Posted: Wed 25. Nov 2020 20:13:58 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Binding will not work until Spirit unit will be operating normally. Now it is in recovery mode. Once firmware is flashed properly, binding satellite should work too.
_________________
Spirit System developer
|
|
| Top |
|
|
|
grant22
|
Posted: Wed 25. Nov 2020 20:20:50 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
It's a different Spirit unit, sir. I have multiple.
2 are on helis and work great
1 is in recovery mode currently
1 is being prepped to be put on a heli and is having the BIND issue
|
|
| Top |
|
|
|
grant22
|
Posted: Wed 25. Nov 2020 23:00:54 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
Please help me out
2 units in good working order are unable to bind. Im sure its something I'm doing wrong, but I've tried everything.
sats will not go into bind mode (they do one quick flash and that's it)
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 26. Nov 2020 14:26:18 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Hello,
you might try version 3.2.1 that was released right now.
I hope it can help you.
_________________
Spirit System developer
|
|
| Top |
|
|
|
grant22
|
Posted: Thu 26. Nov 2020 15:28:52 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
Thank you VERY much. I’ll give it a try
|
|
| Top |
|
|
|
grant22
|
Posted: Thu 26. Nov 2020 16:14:43 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
It still will not enter bind mode. Satellite gives one quick blink and that's all.
Should I try an older firmware and software which allows binding?
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 26. Nov 2020 17:08:16 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Oh, this mean that there is no problem with firmware. But very likely your Receiver type is not set to Spektrum DSM2/X.
Only then binding will work.
_________________
Spirit System developer
|
|
| Top |
|
|
|
grant22
|
Posted: Thu 26. Nov 2020 18:09:20 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
Hi,
Ive selected DSMX under receiver type many times. I've even tried running the wizard to the end and saved the settings first, then tried binding.
I've really tried everything. I've tried different sats, different wire, different usb cable, different power sources.
I've followed the instructions to the letter and I'm running out of ideas here.
|
|
| Top |
|
|
|
grant22
|
Posted: Thu 26. Nov 2020 18:16:20 |
|
Joined: Fri 13. Sep 2019 1:20:17
Posts: 21
|
|
I tried using another receiver and bound the sat to my transmitter that way. It bound, but then when I bring it over to the Spirit, there's no connection.
I just tried resetting both spirits to factory settings and saving the DSMX choice again.
still not working (not entering bind mode)
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: mainstreet and 43 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
