|
It is currently Sun 24. Nov 2024 17:09:22
|
View unanswered posts | View active topics
| Author |
Message |
|
Till
|
 Posted: Mon 08. Jun 2020 17:50:43 |
|
Joined: Sat 06. Jun 2020 14:50:22
Posts: 17
|
Thank you 
|
|
| Top |
|
 |
|
Rouven
|
Posted: Thu 11. Jun 2020 10:58:04 |
|
Joined: Thu 11. Jun 2020 10:47:31
Posts: 5
|
|
Hello,
I have copied the previously provided files to the "Devices" directory and the configuration is now also available with pictures. Nevertheless I have still a problem with the telemetrie port E2 (outermost left connection port, lowest pin), it does not transmit any telemetrie data. When I connect the same sensor to E1, it works. It also works when I connect the sensor to EXT (outermost left connection port, upper pin), but then the Spirit RS cannot be accessed anymore via the device manager.
Unfortunately I cannot configure port E2 in the device manager and require port E1 already for backup power device.
Maybe anybody could give me short instructions how to fix it.
Thank you and best regards,
Rouven
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 11. Jun 2020 11:06:18 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
| Top |
|
|
|
Rouven
|
Posted: Thu 11. Jun 2020 11:29:51 |
|
Joined: Thu 11. Jun 2020 10:47:31
Posts: 5
|
|
Thank you for your quick response.
I think I have already used EXT port. The signal pin of the sensor has been connected to the "EXT/RPM/E2" port to the lowest pin, as described in your manual. Unfortunately it doesn't work...
Regards,
Rouven
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 11. Jun 2020 11:33:53 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
For sure it will work, possibly the sensor was not powered from the same power source or from a correct port.
This might be reason why it does not work.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Rouven
|
Posted: Thu 11. Jun 2020 11:45:25 |
|
Joined: Thu 11. Jun 2020 10:47:31
Posts: 5
|
|
No it doesn't work. I change only one single pin from port "EXT/RPM/E2" lowest pin to "E1" topmost pin and it works...
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 11. Jun 2020 11:52:59 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Can you tell me what type of sensor it is?
_________________
Spirit System developer
|
|
| Top |
|
|
|
Rouven
|
Posted: Thu 11. Jun 2020 11:55:21 |
|
Joined: Thu 11. Jun 2020 10:47:31
Posts: 5
|
|
It is a Kontronik KOLIBRI 90 LV and set to Jeti telemetry.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 11. Jun 2020 12:09:26 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Ah, it is likely this require EX BUS protocol. But EXT port is configured for JETIBOX/Sensor.
This is reason why it is not working, because EXT port is only for standard sensors.
On the other hand you can connect your ESC with Spirit ESC telemetry at the SAT port.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Rouven
|
Posted: Thu 11. Jun 2020 12:13:22 |
|
Joined: Thu 11. Jun 2020 10:47:31
Posts: 5
|
|
Thank you for the quick response.
Yes it uses EXBus, since E1 is configured to that and it works...
So I use an alternate connection setting.
Thank you for your help!!
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 25 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
