|
It is currently Sun 24. Nov 2024 16:58:04
|
View unanswered posts | View active topics
| Author |
Message |
|
helimb
|
 Posted: Wed 03. Jun 2020 15:36:40 |
|
Joined: Sat 18. Jan 2020 15:34:47
Posts: 23
|
|
...little problem:
I assign channel 11 to:
- F: Geo-Link Position Halten
- F: Geo-Link Höhe Halten
In the Off-position from the switch it shows "Zustand: Aus" and "Zustand An(2)"
why not also "Zustand: Aus" ?
>> see attached Screenshots...
greetings
| Attachments: |
Kanalzuordnung2.jpg [ 162.12 KiB | Viewed 254 times ]
|
Kanalzuordnung1.jpg [ 159.58 KiB | Viewed 254 times ]
|
|
|
| Top |
|
 |
|
buttles
|
Posted: Wed 03. Jun 2020 18:28:52 |
|
Joined: Tue 16. Jun 2015 14:37:10
Posts: 156
|
|
You have one of the two available Alt Hold modes selected. Check the online Geolink Manual to see which mode you want then set the endpoints\subtrim of the switch to match your Position Hold mode. You may need to Reverse a switch.
|
|
| Top |
|
|
|
FrankFuss
|
Posted: Wed 03. Jun 2020 18:50:09 |
|
Joined: Tue 17. Mar 2015 3:10:20
Posts: 113
|
|
For Position Hold, Off is -100%. For Altitude Hold, Off is 0%. Can you map the same switch to to different channels which you can control differently? Like one channel from -100% to 100% and the other channel from 0% to 100%.
|
|
| Top |
|
|
|
helimb
|
Posted: Wed 03. Jun 2020 20:04:54 |
|
Joined: Sat 18. Jan 2020 15:34:47
Posts: 23
|
|
| Top |
|
|
|
buttles
|
Posted: Wed 03. Jun 2020 21:22:09 |
|
Joined: Tue 16. Jun 2015 14:37:10
Posts: 156
|
|
Are you using a two or three position switch? The issue you have is Position hold only needs a two position switch but Alt hold 'should' have a three position switch. If you are using a two position switch decide which mode of Alt hold you want and play with Reversing and Endpoints\Subtrim to get both Alt and Position hold to work together.
|
|
| Top |
|
|
|
helimb
|
Posted: Thu 04. Jun 2020 12:57:02 |
|
Joined: Sat 18. Jan 2020 15:34:47
Posts: 23
|
|
I tested the Position Hold mode (chap. 5 "Geolink Features") this morning.
The heli was stable but I could't control the heli with the swashplate-stick
in the horizontal level. There was no influence.
The blue led from the GeoLink-modul was on.
What can be wrong ?
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 04. Jun 2020 13:10:55 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Maybe stick priority is too low - please increase value for Stabi/Stick Priority - for example to 10. Stabi/Function can be configured as Coaxial.
_________________
Spirit System developer
|
|
| Top |
|
|
|
helimb
|
Posted: Thu 04. Jun 2020 15:42:49 |
|
Joined: Sat 18. Jan 2020 15:34:47
Posts: 23
|
|
I changed "Direkt Steuer Anteil: 4" and
"Knüppel Priorität: 10".
Hopefully it will work...
| Attachments: |
Stabi - Koaxial - Knüppelpriorität.jpg [ 151.47 KiB | Viewed 191 times ]
|
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 32 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
