|
It is currently Mon 25. Nov 2024 19:09:53
|
View unanswered posts | View active topics
| Author |
Message |
|
mb-1953
|
 Posted: Sat 27. Jan 2018 19:41:56 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
I have a 2nd TDR2, I downloaded the 2.4.7 fix but the retracts won't respond. Same as before, a servo will work but the etract actuator won't. If I lower the signal of the servos to below 150, the retract will work. Was the download a one time use? Stuck again.
Mike
|
|
| Top |
|
 |
|
ZeXx86
|
Posted: Sat 27. Jan 2018 20:12:28 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
No, the version should be still the same.
Please check what I have written eaerlier. If you are using AUX2 port, then there is same frequency as for the Throttle.
_________________
Spirit System developer
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sat 27. Jan 2018 22:54:37 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
I was using aux3. I'll try to change it around.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sat 27. Jan 2018 23:06:02 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
I am little bit confused. AUX3 port is not in the unit at all.
_________________
Spirit System developer
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sat 27. Jan 2018 23:36:56 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
I have aux 3 output on channel 8, I assigned the top right side of channel mapping for output on ch0, and assigned channel 8. I tried to use aux 2 by inhibiting channel 7 which I use for bank switching (governor channel), but still couldn't get the retracts to move, a servo moves fine. I copied the program in my tx (dx9) from the other tdr2 that works. Now I don't know what to do.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sun 28. Jan 2018 8:18:16 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Did you tried it with a servo? This can tell as that all is OK.
_________________
Spirit System developer
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sun 28. Jan 2018 14:15:57 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
Yes I tried with a servo, the servo operates as one would expect. Also if I change the servo output to 150hz the retract will work connected to channel 0.
Last edited by mb-1953 on Sun 28. Jan 2018 16:09:24, edited 1 time in total.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sun 28. Jan 2018 16:07:43 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Please check that the General - Governor/Throttle - Throttle Frequency is at 60Hz. The only explanation that it does not work is it can operate only at 50Hz.
Personally I dont understand why manufacturers can't add support for higher frequencies as even some normal receivers are operating at 100Hz.
50Hz was used in analog era.
_________________
Spirit System developer
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sun 28. Jan 2018 16:12:20 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
The throttle frequency is at 60. If the servo output is 150 the retracts work so I think that the threshold is not 50hz. Is it possible that the channel 0 output is the same as the other servos?
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sun 28. Jan 2018 16:38:43 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
So I have been confused all along. Your reference to aux 2, was on the spirit pro, I now realize. I thought it was a reference to aux2 in my tx. I reconnected the wires with the retracts to aux2 on the spirit pro, reflashed the download you posted and now it works!!!!!!
Sorry my confusion made this more difficult for you.
Mike
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 1 guest |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
