|
It is currently Sun 24. Nov 2024 10:18:29
|
View unanswered posts | View active topics
 
|
Page 1 of 1
|
[ 7 posts ] |
|
| Author |
Message |
|
mb-1953
|
 Posted: Sat 27. Feb 2016 17:09:55 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
My pro wanted me to first download 1.3.2, which I didn't have. I downloaded the version that was posted on helifreak by Tomas. After the download the software said congratulations on downloading version 2.0. The pro will not connect and when I apply power the red light blinks once but that is it. Help please
|
|
| Top |
|
 |
|
Coco66
|
Posted: Sat 27. Feb 2016 17:15:00 |
|
Joined: Sun 26. Jul 2015 8:17:50
Posts: 433
Location: Madrid, Spain / Torino, Italy
|
|
Use the Recovery mode:
1. Start the software and then press No when prompted to Demo mode.
2. Select the firmware in the Update tab and press the flash button (you should see Recovery mode label immediately).
3. Connect the battery to your model (with USB interface connected). Then you should see a new flashing progress.
You do it with software 2.0.0 and load firmware 2.0.0
You will have to set it up from scratch after done.
_________________
Oxy 2 ♦ X-Vert ♦ Warp 360 ♦ Blade 450X ♦ Blade 450X Nightflyer ♦ Goblin 500 (RIP) ♦ 2 X mCPX v2 ♦ night fly mQX ♦ LadyMQX ♦ nano QX ♦ nano QX FPV ♦ Inductrix ♦ DX8 G1
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sat 27. Feb 2016 18:21:39 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Please make sure that you have correct driver installed so it can't happen again. What is your operating system?
_________________
Spirit System developer
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sat 27. Feb 2016 19:22:31 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sat 27. Feb 2016 19:28:42 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
I tried what coco suggested but there is no flashing, the screen does say recovery mode but nothing happens.?
|
|
| Top |
|
|
|
mb-1953
|
Posted: Sat 27. Feb 2016 19:53:29 |
|
Joined: Tue 03. Mar 2015 15:55:50
Posts: 98
|
|
I was able to first recover 1.3.2 and then 2.0. Looks like I am out of the woods. Thank you
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Sat 27. Feb 2016 20:07:14 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
I recommend to try recovery mode with 2.0.0 software. It might help you.
Also you can try to disconnect ELE/PIT/AIL cable that is in the unit.
_________________
Spirit System developer
|
|
| Top |
|
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 31 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
