Version 1.4.0 was released!
It brings many new features and improvements:
- Support for brand new Spirit 2 unit:
- Full support for new Spirit units with the latest generation hardware and design.
- Initial support for GeoLink modules:
- Allows recording each second of your flight.
- Many new features are comming soon!
- GeoLink modules are supported by all Spirit units!
- Built-in protractor for GeoLink mounting delection measurement.
- Interactive Google Maps in the Spirit Settings for viewing Flight Logs.
- NOTE: For further details please visit GeoLink Manual.
- Spirit Settings startup:
- Software startup procedure was updated to be more user friendly.
- ESC Telemetry support for YGE LVT/HVT ESCs:
- Telemetry variables:
- Battery Voltage
- Battery Current
- BEC Voltage
- Consumed Capacity
- ESC Temperature
- RPM
- NOTE: Use modified JST-Servo cable to connect the ESC with unit.
- NOTE: Telemetry guide is available at the Wiki pages.
- Spektrum DSM2/X satellites:
- Support for up to 4 satellites with Spirit 2 and Spirit Pro units - Primary, Secondary ports, RUD port - with Spektrum adapter, RUD/AIL - with Spektrum adapter or SPM4649T.
- Support for up to 3 satellites with Spirit units - Primary port, RUD port - with Spektrum adapter, RUD/AIL - with Spektrum adapter or SPM4649T.
- Support for up to 3 satellites with μSpirit units - Primary port, RUD port - with Spektrum adapter, RUD/AIL - with Spektrum adapter or SPM4649T.
- Futaba Telemetry improvements:
- ROXXY ESC sensor changed to KONTRONIK.
- NOTE: Set KONTRONIK sensor at SLOT 8 in the SENSORS menu.
- Compatibility with the latest firmware and all FASSTest radios.
- Futaba S.BUS improvements:
- S.BUS2 connection stability was improved.
- Flying Wing has optional Rudder support:
- When using Flying Wing model type you can also control Rudder channel - servo can be connected at the CH4 port.
- Spirit Settings - Channel Mapping:
- Support for 16 channels with all digital protocols!
- 16 channels available with Spektrum DSM2/X, SRXL/SUMD, SBUS, EX BUS protocols.
- Spirit Settings - Special features:
- Possibility to assign up to 6 special features!
- Pilot can engage 2 times more features with a dedicated channels.
- Configuration of the Special features is more clean now. Unused options are not visible.
- NOTE: Mapping for all Special features are cleared after the update. Please set them again.
- Jeti UDI-16 and SRXL-16 protocol:
- 16 channel protocols are fully supported now.
- Support for 16 channel Failsafe:
- Failsafe can be configured for all 16 channels now.
- New Futaba S.BUS2 verification:
- S.BUS2 connection can be detected automatically at any point - during or after initialization.
- New Futaba S.BUS2 Telemetry:
- Telemetry is compatible with all Futaba FASSTest radios now.
- New Kontronik TelMe ESC Telemetry:
- Brand new protocol from Kontronik ESCs is fully supported with all Spirit units.
- TelMe protocol is supported by Kontronik Kolibri, Jive Pro and Kosmik ESCs.
- Available for Spektrum, Futaba, Jeti, Graupner and FrSky radios.
- Telemetry cable with JST connector is connected at the primary Satellite port.
- CABLE: Cable provided with the ESC can be used together with JST-Servo cable.
- CABLE: Old Telem KONTRONIK cables can be used together with JST-Servo and a small modification.
- CABLE: New Telem KONTRONIK v2 cable is available in our eshop.
- NOTE: No Kontronik TelMe module is needed. Only the cable between ESC and Spirit unit.
- ESC Telemetry update:
- BEC current is now available as a Telemetry variable with selected models of Castle, YGE and Kontronik ESCs.
- Available for Spektrum and HoTT radios.
- Backup Oscillator:
- Flight log will display notification if a Backup oscillator is used.
- Spektrum DSM2/X protocol:
- Improved Binding compatibility with non-Spektrum satellites.
- Spirit Settings - Diagnostic tab:
- Diagnostic tab was redesigned for a better clarity.
- All features are displayed in the Diagnostic tab to see whether they are enabled and engaged.
- Gyro Gain bar will display also a negative values.
- Spirit Settings - Automatic Save:
- New Auto Save feature for saving changes to the unit instantly.
- Spirit Settings for Linux:
- Updated runtime library for supporting the latest Linux distributions.
- OpenTX integration update:
- FIX: S.Port connection with FrSky RX8R Pro receiver is working properly on all Spirit units now.
New configuration of the Special functions in General/Channels is required (if used).
Update for the Spirit units is available in our Download section.
|