| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Goblin 570 tail overshooting on fast right turns https://www.spirit-system.com/phpBB3/viewtopic.php?f=21&t=5840 |
Page 1 of 2 |
| Author: | zino [ Thu 12. Oct 2023 15:21:25 ] |
| Post subject: | Goblin 570 tail overshooting on fast right turns |
Hi i have a goblin 570 tail locks and hold good no wagging no any problem during hovering. When i fly fast and i do right turn then tha tail is doing fast overshooting Can someone give me some tips for that issue? Thanks |
|
| Author: | ZeXx86 [ Thu 12. Oct 2023 20:42:01 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
What is your Pitouette consistency and Rudder delay? |
|
| Author: | zino [ Fri 13. Oct 2023 6:14:28 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Hi the rudder delay is 2 and pirouette consistency is 177. My rudder servo is kst bls805x Some extra infos, my gyro gain is at 70% i try 80% but now changes Rudder dynamic is 6. Thanks |
|
| Author: | zino [ Fri 13. Oct 2023 10:59:42 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Any tips please? |
|
| Author: | ZeXx86 [ Fri 13. Oct 2023 11:03:59 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Hello, your tail servo is little bit specific and require different servo arm length. Can you also let me know what are your current Rudder End-point values? Changing Rudder servo arm length can help a lot. Your settings looks good. You can set Rudder Delay to 0. Also make sure that tail slider (if present) is not touching the push rod or even that push rod is not bent there. Any friction there will make tail performance worse. Decreasing Gyro gain will help for sure too. Then if needed, you can set Rudder Revomix to 2-3. Revomix shouldn't be needed normally in any case, but can be helpful when using lower Gyro Gain. |
|
| Author: | zino [ Fri 13. Oct 2023 11:45:29 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Hi the tail end points are both 90 |
|
| Author: | zino [ Fri 13. Oct 2023 11:49:20 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Do you think that i must reduce a bit rudder end point to the side that makes overshooting? So to decrease litle the angle of tail blades? |
|
| Author: | ZeXx86 [ Fri 13. Oct 2023 11:51:38 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
You can try to make rudder servo arm shorter if possible. Then please readjust rudder end-points. |
|
| Author: | zino [ Fri 13. Oct 2023 11:54:55 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Ok i will move ball link one hole up but what you think is godd value for end points, 90 -100 is ok? |
|
| Author: | zino [ Fri 13. Oct 2023 11:55:20 ] |
| Post subject: | Re: Goblin 570 tail overshooting on fast right turns |
Ok i will move ball link one hole up but what you think is godd value for end points, 90 -100 is ok? |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|