|
It is currently Fri 22. Nov 2024 19:44:16
|
View unanswered posts | View active topics
| Author |
Message |
|
john1127
|
 Posted: Thu 02. Jul 2015 2:27:18 |
|
Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
|
|
Got it flying pulls hard to the right in srab mode wash is level, whats wrong, stabil but need left stick?
|
|
| Top |
|
 |
|
ZeXx86
|
Posted: Thu 02. Jul 2015 14:35:51 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Hello,
when starting in the stabilisation mode it is recommended to start the helicopter on a flat surface.
If you will tilt the helicopter to one side for a while, it will remember it and will stay at this position. So returning direction can be changed even it starts in angle.
_________________
Spirit System developer
|
|
| Top |
|
|
|
john1127
|
Posted: Mon 13. Jul 2015 18:55:17 |
|
Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
|
|
No on flat serface and swash level still drift, and piroets cant do cause drifts all over piro direction good HELP
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Mon 13. Jul 2015 20:03:18 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Can you measure vibration level in the software, please? Maybe the level is extremely high, so it can cause the problem.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Scott H
|
Posted: Tue 14. Jul 2015 3:06:07 |
|
Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
|
|
Just out of curiosity, how do you level your swash?
|
|
| Top |
|
|
|
john1127
|
Posted: Tue 14. Jul 2015 20:26:48 |
|
Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
|
|
90 arms level swash with leveler and 0 degrees on blades
|
|
| Top |
|
|
|
Scott H
|
Posted: Tue 14. Jul 2015 21:08:24 |
|
Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
|
|
Is there any chance that after you leveled it with subtrim in the software that you did not save the settings?
|
|
| Top |
|
|
|
john1127
|
Posted: Tue 14. Jul 2015 21:51:27 |
|
Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
|
|
no but in solftware does it put servo to 90 and then use sliders to 90 arms
|
|
| Top |
|
|
|
Scott H
|
Posted: Tue 14. Jul 2015 22:06:59 |
|
Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
|
|
Well I think you are saying in the subtrim tab that the software locks the servos at middle position (90 - you call it) and so at that point your use the sliders to make sure the arms are exactly at 90 degrees to the swash.
My point was that you actually saved those settings, cause if you didn't than the servos would revert to the old position.
Seems like it's either the vibration (what heli is this again?) or a swash that is no longer level.
|
|
| Top |
|
|
|
john1127
|
Posted: Tue 14. Jul 2015 22:13:44 |
|
Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
|
|
I saved them Its a blade 450x log doesn't say anything about vibes but tail does shake till take off speed
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 32 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
