| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Questions about Rescue https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=636 |
Page 1 of 2 |
| Author: | bell222 [ Sun 08. Mar 2015 4:21:27 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
i have checked piro and that is correct i will check the stab after flight and see what the swash does |
|
| Author: | Ralf.Grum [ Thu 19. Mar 2015 20:36:20 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Hello, what can you do if the Piro.Option OK, vibrations do not exceed a maximum of 12 but the swashplate tilts heavily after the flight to the right. What do I do? please excuse my bad english, google translator. greeting Ralf |
|
| Author: | ZeXx86 [ Thu 19. Mar 2015 21:05:39 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Hello, can you check point 2) - alignment of the unit? Do you fly some acrobatics or harder 3D? |
|
| Author: | Ralf.Grum [ Thu 19. Mar 2015 21:24:50 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
2. to have different pads have tried. And the position of the Spirit also changed already on the Heli. I only fly flight no 3D. beginner when I start mode in the stability it works. Excuse my bad english greeting RAlf |
|
| Author: | ZeXx86 [ Thu 19. Mar 2015 21:34:41 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Thanks for the info. Can you please verify pirouette optimization once again? If you are doing some additional settings it may need to be changed. |
|
| Author: | linux-user [ Thu 19. Mar 2015 21:42:18 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Hi Ralf it may be still vibrations which you would only see with the blades mounted. or: http://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=494 Manfred |
|
| Author: | Ralf.Grum [ Thu 19. Mar 2015 21:54:26 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
ZeXx86 wrote: Thanks for the info. Can you please verify pirouette optimization once again? If you are doing some additional settings it may need to be changed. the pirouette optimization I have before and after the flight check is OK it is a TRex 700 clone The rotor blades are new, main and tail rotor blades, blade shaft bearings, all new bearings Blades balanced. 
|
|
| Author: | ZeXx86 [ Thu 19. Mar 2015 22:02:48 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Can you measure vibrations on Y - Aileron axis with tail blades on, please? Mostly tail blades are most problematic, so it can add huge spikes. Then we can be sure it can't be vibration problem. Do you have latest 1.1.0 version? If you do not see High Vibration event in the log, than it should be OK. |
|
| Author: | Ralf.Grum [ Thu 19. Mar 2015 22:14:02 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
I will do it tomorrow with tail rotor blades s test Log flight after the Last 
|
|
| Author: | ZeXx86 [ Thu 19. Mar 2015 22:21:35 ] |
| Post subject: | Re: Troubleshooting - Rescue/Stabilisation is inprecise |
Thanks for the log. OK we will see then. Did it happened earlier or it is new problem? In the worst case I can send you some unit to compare or you can send us the unit to recheck if you wish. |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|