| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Calibration failure https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=6121 |
Page 1 of 3 |
| Author: | raceboy1 [ Wed 05. Jun 2024 18:56:33 ] |
| Post subject: | Calibration failure |
Ok here’s what you asked The GeoLink is Brand New Of course the cable is also brand new It’s wired into the Sat 2 port of the Spirit FLB The FLB unit is controlling the Heli in all stick movements as it should I updated the GeoLunk to the latest firmware before installing The FLB was also updated before installing I’m using a Sprektrum AR8012 SRXL which is wired into the Sat 1 port The software is seeing the Geolink and shows all the info on the Info page Like I said, when I select the Calibration Tab I never see a blinking blue light, only a solid green light When I installed the Geolink , I selected the Geolink check box then powered everything down, including the software and then brought everything back up again |
|
| Author: | ZeXx86 [ Wed 05. Jun 2024 20:22:33 ] |
| Post subject: | Re: Calibration failure |
Hello, the receiver is not connected correctly. It should be connected with JETI integration cable at the RUD + AIL pin. If you power receiver from BEC it could burn up both GeoLink and Spirit. By the way you created third thread here. Please do not open another thread. Just click at the Reply button. |
|
| Author: | raceboy1 [ Wed 05. Jun 2024 22:30:00 ] |
| Post subject: | Re: Calibration failure |
The SRXL2 wiring should be correct The cable is coming out of the SRXL2 port on the receiver The ground and positive are going to the RUD Port The Orange wire is going to the top pin of the ( ELE/Pit/Ail) port Just how it shows in the manual John |
|
| Author: | raceboy1 [ Wed 05. Jun 2024 23:10:51 ] |
| Post subject: | Re: Calibration failure |
Is there any way that you could take over my computer to figure out what is going on John |
|
| Author: | raceboy1 [ Thu 06. Jun 2024 0:36:15 ] |
| Post subject: | Re: Calibration failure |
Here’s the balance of my wiring for you to check Sys. To computer 0. Blank 1. L aileron 2. Elevator 3. R aileron 4. Rudder Aux 2 BEC output from ESC Aux 1. Throttle Signal from ESC Rpm wire from ESC to bottom pin of (Elle/pit/ail) Data wire from ESC to Sat 1 SAT 2. Geo link Hobbywing Platinum v4 ESC 120 a All controls on Heli work as they should And I have full Telemetry including RPM’s |
|
| Author: | toni67 [ Sat 08. Jun 2024 11:22:10 ] |
| Post subject: | Re: Calibration failure |
raceboy1 wrote: The SRXL2 wiring should be correct Only you're using Satellites. But you wrote: raceboy1 wrote: I’m using a Sprektrum AR8012 SRXL which is wired into the Sat 1 port That's not a Satellite! For you the correct chapter of the manual is No 11. https://manual.spirit-system.com/index.php?title=Wiring |
|
| Author: | raceboy1 [ Sat 08. Jun 2024 14:11:50 ] |
| Post subject: | Re: Calibration failure |
Ok, I moved the signal wire of XRXL from the ail port back into the rud port Now I’m not getting a throttle signal and my motor just beeps Also, I tried the compass calibration again and when power down and power back up the Heli The Geolink still goes straight to a solid green light John |
|
| Author: | raceboy1 [ Sat 08. Jun 2024 14:52:27 ] |
| Post subject: | Re: Calibration failure |
I miss spoke. I don’t have any transmitter controls with it wired this way |
|
| Author: | ZeXx86 [ Sat 08. Jun 2024 16:53:00 ] |
| Post subject: | Re: Calibration failure |
Your wiring to AIL pin + RUD port was correct for SRXL2 receiver. I want to make clear how the Calibration should be triggered. First you open Spirit Settings. Then open General - GeoLink. Then go to Module tab and click at the Calibration button. Is this working for you? It should open window that must be confirmed with OK. Then after powerup you should be able to calibrate. |
|
| Author: | raceboy1 [ Sun 09. Jun 2024 12:10:12 ] |
| Post subject: | Re: Calibration failure |
Everything in your last post occurs as stated In the calibration screed that you have to agree to It also tells you that when you power the unit back up, you will see a flashing blue light, Which indicates that the unit is in calibration mode This never happens, it just goes to a solid Green light. And no matter how much you move the Heli around that never changes I think this unit needs replacing. John |
|
| Page 1 of 3 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|