| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Need Help with the geolink V2 & Spirit Pro https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=5654 |
Page 1 of 2 |
| Author: | Timtom [ Thu 04. May 2023 17:22:39 ] |
| Post subject: | Need Help with the geolink V2 & Spirit Pro |
Attachment: 20201117_102755_Burst01[1].jpg [ 2.03 MiB | Viewed 462 times ] I have a spirit Pro , old hardware , Version 3.5.0 with geolink 1.3.3 Radio : Futaba T14SG with R7003 SB Because I only use the altitude limit i progged a switch at Chanel 8 to switch on the function . when I turn on the function in flight, the heli shoots up even though it's in range ( low limit 5m / high 50 ) I'm assuming everything is installed correctly? Can someone help me ? |
|
| Author: | ZeXx86 [ Fri 05. May 2023 12:17:42 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
Hello, this behavior is correct. After activation the model should go up for around 1.5 seconds. Then you can continue with flying and Altitude Limit will work in the "background". |
|
| Author: | Dr.Fleming [ Fri 05. May 2023 14:55:54 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
Hello Zex, looks that you not read carefully what the users problems write here. Why was my previous message deleted ZeXx86 wrote: Hello,
this behavior is correct. After activation the model should go up for around 1.5 seconds. Then you can continue with flying and Altitude Limit will work in the "background". |
|
| Author: | Timtom [ Fri 05. May 2023 17:31:44 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
while the altitude limit function is on, the heli goes up and down all the time until I turn it off . |
|
| Author: | franz88 [ Sun 07. May 2023 7:34:41 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
you solved? I encountered a similar thing with rescue automatic spirit gt. write step by step how you configured the geolink. how do you avoid slipping around the tube? (geolink support) tightening the two screws is not enough |
|
| Author: | Habásek [ Sun 07. May 2023 7:54:54 ] | |||
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro | |||
https://store.spirit-system.com/cs/prislusenstvi/45-spirit-geolink-drzak.html I have this holder, without screws, you use double-sided adhesive tape like the one for the units (or similar) and zip ties.
|
||||
| Author: | franz88 [ Sun 07. May 2023 8:12:07 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
is good. did you put the bioadhesive both between geolink and support and between support and tail tube? is important between tube and support why the clamps with vibrations they can rotate the geolink support. Listen I use the geolink and it is ok, only that it can be escaped a detail in the programming. Think I forgot geometry 6degress and during flight normal the altitude limit is perfect. each control unit has strengths and weaknesses If you connect spirit and geolink to the software and lift the model with your hands the altitude in geolink - info is read accurately? to me even if I move by little is read This test fails with as many satellites as possible. This bench test and after you have a way to put logs or telemetry? me before using it I lifted the model into the air and on the radio I could see how it read the altitude you attach setting |
|
| Author: | Timtom [ Sun 07. May 2023 8:46:29 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
the specially milled bracket is very tight because it has a clamp. The supplied pad sits between the module and holder. Data such as altitude are displayed correctly in the software 6° ? The heli flies absolutely OK without geolink. It's a real shame that there aren't complete instructions |
|
| Author: | Rdlx3m [ Sun 07. May 2023 9:49:42 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
Timtom wrote: the specially milled bracket is very tight because it has a clamp. The supplied pad sits between the module and holder. Data such as altitude are displayed correctly in the software 6° ? The heli flies absolutely OK without geolink. It's a real shame that there aren't complete instructions Hmm.. does you limit setting have some of the same characteristics like my heli when i turn on return to home?? https://youtu.be/YPp81ieFFcg |
|
| Author: | Timtom [ Sun 07. May 2023 10:00:37 ] |
| Post subject: | Re: Need Help with the geolink V2 & Spirit Pro |
the difference with my problem is that the heli makes a lot more work. So more meters up and down |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|