Spirit System
https://www.spirit-system.com/phpBB3/

[SOLVED] Spirit2 - fport - No telemetry
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=5637		 Page 1 of 3
Author:  jjuk [ Sun 16. Apr 2023 18:38:06 ]
Post subject:  [SOLVED] Spirit2 - fport - No telemetry
I have set up a Spirit 2 (v3.5.0) with a r-xsr f.port receiver running ACCST v1.

The spirit 2 is receiving channel information correctly. It's fully operational.

The spirit 2 doesn't seem to be sending any telemetry information back to the radio, also the OpenTx scripts are not loading (because the spirit 2 isn't sending telem back to the radio).
Author:  ZeXx86 [ Sun 16. Apr 2023 19:18:40 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Hello,

we have exactly this receiver and it works with F.Port well, including telemetry and integration.
Do you have something else connected to F.Port bus?
Is F.Port receiver type configured in the Spirit unit?
Author:  MegaHz [ Sun 16. Apr 2023 23:23:34 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Make sure you have the connector plugged in the right way. The exact situation happened to me. in ACCST you should be on S.PORT technically
Author:  jjuk [ Sun 16. Apr 2023 23:44:54 ]
Post subject:  Re: Spirit2 - fport - No telemetry
My r-xsr is connected as follows:

https://oscarliang.com/wp-content/uploa ... 24x591.jpg

Code:
Un-inverted smart port -> Spirit 2 ELE/PIT/AIL top pin
RX Power               -> Spirit 2 RUD top pin
RX Gnd                 -> Spirit 2 RUD bottom pin


Receiver is set to "FrSky F.Port"

I have full control, but no telem.
Author:  ZeXx86 [ Mon 17. Apr 2023 12:58:04 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Maybe problem is here:
RX Power -> Spirit 2 RUD middle pin
Author:  jjuk [ Mon 17. Apr 2023 14:32:20 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Sorry that was a typo. The power is connected to the centre pin.
Author:  Vector [ Mon 17. Apr 2023 14:38:03 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Did you updated r-xsr with last FW ? And did you put rx in f.port mode?
Author:  jjuk [ Mon 17. Apr 2023 20:17:35 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Here are all the software versions that I'm using:

Spirit 2 v3.5.0, 4ds file attached.
Attachment:
500x fport with stab.4ds [255 Bytes]
Downloaded 41 times


R-XSR:
I'm running RXSR-FPORT_LBT_ACCST_191128.frk from here:
https://www.frsky-rc.com/wp-content/upl ... 191128.zip
The receiver is showing a green and a blue LED, which I believe means green=bound, blue=fport.

Transmitter:
Running OpenTx 2.3.14, and Spirit integration https://www.spirit-system.com/dl/opentx ... 4.3-en.zip

I have full channel control of the Spirit 2, all channels are working, so the receiver must be outputting f.port to the spirit, but the spirit isn't sending telem to the receiver.
Author:  Vector [ Mon 17. Apr 2023 23:25:27 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Try this ACCST D16 v2.1.0, ACCST D16 v2.1.1(F.Port firmware update only )
GT 3.5 + R-Xsr 2.1.1 LBT and EdgeTX 2.8 integration 3.4.3 everything works great.
Author:  jjuk [ Mon 17. Apr 2023 23:42:13 ]
Post subject:  Re: Spirit2 - fport - No telemetry
Just flashed the transmitter to ACCST v2.1.0, and the r-xsr receiver to "RXSR_ACCST_2.1.1_Fport_LBT.frk."
https://www.frsky-rc.com/wp-content/upl ... v2.1.1.zip

I have full control of the model, but no telem is being sent back to the radio.
Page 1 of 3 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/