| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Return to home https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4564 |
Page 1 of 2 |
| Author: | Bill-kraken-700 [ Mon 22. Feb 2021 21:54:54 ] |
| Post subject: | Return to home |
Hi there the manual and software seems to contradict each other when return to home on 4 is enabled the manual states it returns to take of position and in the software it states return to power on position. Can anyone verify which is correct? |
|
| Author: | Bill-kraken-700 [ Tue 23. Feb 2021 10:45:20 ] |
| Post subject: | Re: Return to home |
Surely some one knows the answer? |
|
| Author: | ZeXx86 [ Tue 23. Feb 2021 14:07:36 ] |
| Post subject: | Re: Return to home |
Hello, there are several modes for Return to Home. 4th function will return model to take off position and is special case of RTH. While the rest will return it to programmed Home point. |
|
| Author: | Bill-kraken-700 [ Tue 23. Feb 2021 14:09:52 ] |
| Post subject: | Re: Return to home |
ZeXx86 wrote: Hello, there are several modes for Return to Home. 4th function will return model to take off position and is special case of RTH. While the rest will return it to programmed Home point. So if I power the heli up on the bench then move it to the take off point it will return to that point it toke if and not over the bench where it was powered up ? |
|
| Author: | ZeXx86 [ Tue 23. Feb 2021 14:13:23 ] |
| Post subject: | Re: Return to home |
Yes, that is correct. But 4th RTH mode must be engaged, not other. You can try it easily in the flight in a high altitude. |
|
| Author: | Bill-kraken-700 [ Tue 23. Feb 2021 14:14:55 ] |
| Post subject: | Re: Return to home |
ZeXx86 wrote: Yes, that is correct. But 4th RTH mode must be engaged, not other. You can try it easily in the flight in a high altitude. Many thanks for your support. One last thing. I read you helped another customer reset the gyro to fix manufacturing process. Can you tell me how I do this ? |
|
| Author: | ZeXx86 [ Tue 23. Feb 2021 15:47:03 ] |
| Post subject: | Re: Return to home |
Hello, this process should be done only in case you have some problem and there is no other solution. Have you encountered something similar? |
|
| Author: | Bill-kraken-700 [ Tue 23. Feb 2021 16:03:45 ] |
| Post subject: | Re: Return to home |
ZeXx86 wrote: Hello, this process should be done only in case you have some problem and there is no other solution. Have you encountered something similar? No not yet. I haven’t test flown yet. |
|
| Author: | Bill-kraken-700 [ Wed 24. Feb 2021 19:36:43 ] |
| Post subject: | Re: Return to home |
ZeXx86 wrote: Hello, this process should be done only in case you have some problem and there is no other solution. Have you encountered something similar? the compass calibration was performed in doors when installing the units should i do this outdoor or will this not matter |
|
| Author: | cracked canopy [ Thu 25. Feb 2021 0:47:40 ] |
| Post subject: | Re: Return to home |
Bill-kraken-700 wrote: ZeXx86 wrote: Hello, this process should be done only in case you have some problem and there is no other solution. Have you encountered something similar? the compass calibration was performed in doors when installing the units should i do this outdoor or will this not matter Its always best to perform compass calibration out doors in an open area. |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|