| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| [SOLVED] DSMX Satellite - channels mixed up https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=429 |
Page 1 of 1 |
| Author: | linux-user [ Thu 15. Jan 2015 17:29:44 ] |
| Post subject: | [SOLVED] DSMX Satellite - channels mixed up |
Hi, I am trying to connect the Spirit-FBL with a DSMX Satellite with DMSX protocol. But channels are terrible mixed up: Watching the Diagnostic-Tab in the config Software the following could be observed: === DSMX === Ch1: from -100% to ~0% moves Throttle from ~0% to +100% moves Aileron Ch2: from -100% to ~0% moves Elevator from ~0% to +100% moves Rudder Ch3: from -100% to ~0% moves Gyro from ~0% to +100% moves Pitch Ch4: from -100% to ~0% moves Bank ========= Channel assignment is: Ch1: T Ch2: A Ch2: E Ch4: R Ch5: Gyro Ch6: Pitch Ch7: Bank So I tried to bind with DSM2 This seems to be working. But even there is a minor issue I don't understand: Although in the TX all Channels are set to be from -100% to +100% the Diagnostic Tab shows values from -98% to 102% My Equipment: - spirit-fw-1.0.25.1.bin - Walkera Devo10 with Deviation FW http://deviationtx.com - original Spektrum DSMX Satellite. - Powersupply: 4xNiMH AA Battery = 4,8V - PC: Linux USB and Android Bluetooth Hope this helps to resolve the issue. Let me know, if I could do anything else to help. Greetings Manfred |
|
| Author: | ZeXx86 [ Thu 15. Jan 2015 17:58:27 ] |
| Post subject: | Re: DSMX Satellite - channels mixed up |
Hello, this TX should be binded with DSM2 as you have did - this is because DSMX in our case require 11ms currently, but this feature is not supported by your TX. With upcoming FW it will be possible to bind it properly to 22ms @ DSMX. All in all, even it is binded as DSM2 it will in reality work as DSMX without any issue. Next issue is very minor - there are nearly always differences between transmitter. Values that are displayed in TX are not the same that unit can see so you should little bit change with Travel Adjust endpoints for these channels. 2% are very small difference, but it can be configured exactly in your TX. This is nothing to worry as it is normal phenomenon. |
|
| Author: | linux-user [ Thu 15. Jan 2015 19:15:05 ] |
| Post subject: | Re: DSMX Satellite - channels mixed up |
ZeXx86 wrote: Hello, DSMX in our case require 11ms currently, but this feature is not supported by your TX. With upcoming FW it will be possible to bind it properly to 22ms @ DSMX. Thanks for your quick and informative reply. I am looking forward to the new FW 
|
|
| Author: | Nafets77 [ Fri 26. Jun 2015 15:37:11 ] |
| Post subject: | Re: DSMX Satellite - channels mixed up |
Hi, Has the issue with European DSMX only using 22ms been solved. It's not mentioned in the change log for v1.2.0. Regards Stefan |
|
| Author: | linux-user [ Fri 26. Jun 2015 20:27:13 ] |
| Post subject: | [solved]: DSMX Satellite - channels mixed up |
Nafets77 wrote: Has the issue with European DSMX only using 22ms been solved. It's not mentioned in the change log for v1.2.0. Yes, solved since v1.1.0 |
|
| Page 1 of 1 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|