| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| [SOLVED] Castle Creations Phoenix Edge HV 80A https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4241 |
Page 1 of 1 |
| Author: | latjo-k [ Mon 24. Aug 2020 10:00:58 ] |
| Post subject: | [SOLVED] Castle Creations Phoenix Edge HV 80A |
Hi A couple of questions abaout this esc,i plan to use the governor in spirit unit the white cable from cc goes to the pit pin in unit ok.But the manual says connect a resistor 10Kohm betwen the white and the red cable for use telemetry?Else use the telem cc cable?I can only se brown red orange on this cable and a shrinktube in the middle. I cant understand this? Can anybody explain? //Latjo |
|
| Author: | ZeXx86 [ Mon 24. Aug 2020 10:17:06 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
Hi, red and orange wires are same as white and red. Pit cable is for rpm sensing for governor. It is 4th wire. And also there is secondary bec cable. Anyway we highly recommend to get telem cc cable. |
|
| Author: | latjo-k [ Mon 24. Aug 2020 10:47:55 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
Ok I order a telem cc cable,whth that the white cable connects direct to the pit pin(for rpm)and the throttle cable connects to telem cc cable and the telem cc csble goes to Trottle on spirit rs unit? am i correct? //Latjo |
|
| Author: | latjo-k [ Mon 24. Aug 2020 10:58:33 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
hi The telem cc cable is on backorder? //Latjo |
|
| Author: | ZeXx86 [ Mon 24. Aug 2020 12:26:53 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
Yes, you are correct. Yes, cable is not in stock, but we will produce them within 1-3 days. |
|
| Author: | latjo-k [ Mon 24. Aug 2020 14:42:03 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
ZeXx86 wrote: Hi, red and orange wires are same as white and red. Pit cable is for rpm sensing for governor. It is 4th wire. And also there is secondary bec cable. Anyway we highly recommend to get telem cc cable. HI Is it then ok to put the 10Kohm resistor between the red and orange cable? //Latjo |
|
| Author: | ZeXx86 [ Mon 24. Aug 2020 14:42:53 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
Yes, this is OK if done properly. |
|
| Author: | latjo-k [ Mon 24. Aug 2020 14:58:17 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
ZeXx86 wrote: Yes, this is OK if done properly. OK Thank you Thomas |
|
| Author: | latjo-k [ Fri 04. Sep 2020 7:25:31 ] |
| Post subject: | Re: Castle Creations Phoenix Edge HV 80A |
Hi The esc is up and running,difficult to get it to arm,find a video on web. Governor working ok and telemetry displays all data as it should. Thanks //Latjo |
|
| Page 1 of 1 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|