don't be confused by input channels ( from RX )
and output channels ( to servos )
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Setup serial satellite 4651T https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4109 |
Page 1 of 1 |
| Author: | alex4orly [ Tue 30. Jun 2020 13:57:15 ] |
| Post subject: | Setup serial satellite 4651T |
in the special section about it, the manual says: Please assign Throttle channel in the General/Channels at Channel 1. But, I have channels 1, 2, 3, 4 assigned as per the manual. So, what to do now? Thank you |
|
| Author: | urgno [ Tue 30. Jun 2020 14:02:09 ] |
| Post subject: | Re: Setup serial satellite 4651T |
don't be confused by input channels ( from RX ) and output channels ( to servos )
|
|
| Author: | alex4orly [ Tue 30. Jun 2020 21:29:56 ] |
| Post subject: | Re: Setup serial satellite 4651T |
urgno wrote: don't be confused by input channels ( from RX ) and output channels ( to servos ) I am confused... I was told to insert the ESC plug into AUX1 on the Spirit - this is as it is now. The 1,2,3,4 are plugs inserted from the Spirit TO the servos : Pitch, Elevator, Ailerone, Rudder In the software however, the Throttle channle is Unassigned, but in the drop down options there is no AUX1 to be selected, so the Throttle is Unassigned The sticks movements are currently activating the WRONG servos So, Not to be confused? |
|
| Author: | urgno [ Wed 01. Jul 2020 11:39:27 ] |
| Post subject: | Re: Setup serial satellite 4651T |
keep in mind that the CH number of the servos has nothing to do with CH numbers in the TX first you connect the SPM4651T to spirit then using spirit settings you choose SRXL2 then you move the sticks and change the channel assigment using the button "Channels" that is near the receiver selection and you have to match the channels that you see in the "Diagnostic" tab is nonsense to change the channel assignment in the TX because some channels have some special preset and btw VERY important is that in your TX you choose 90° swashplate ( H1 ) is the spirit that then will do all the mixing for the 120° swashplate |
|
| Author: | ZeXx86 [ Wed 01. Jul 2020 12:56:53 ] |
| Post subject: | Re: Setup serial satellite 4651T |
By default channel mapping with SRXL2 will require very likely no or almost no changes. So it should be plug and play, unless you will completely change radio profile. So default settings = will work immediately. Onyl SRXL2 should be selected and Throttle channel assigned in the Channels window. |
|
| Author: | alex4orly [ Wed 01. Jul 2020 13:41:26 ] |
| Post subject: | Re: Setup serial satellite 4651T |
ZeXx86 wrote: By default channel mapping with SRXL2 will require very likely no or almost no changes. So it should be plug and play, unless you will completely change radio profile. So default settings = will work immediately. Onyl SRXL2 should be selected and Throttle channel assigned in the Channels window. Sorry, the term in my mind should be ESC, becasue that stick controls two functions, motor and pitch My ESC is plugged into AUX1, I followed the instructions, but 1) In the software it shows as unassigned, AND 2) IF I try to assign throttle to something - AUX1 is NOT an option in the drop down list So? Thanks |
|
| Author: | urgno [ Wed 01. Jul 2020 13:41:39 ] |
| Post subject: | Re: Setup serial satellite 4651T |
OT want to point out that I am correctly receiving the reply notification /OT alex4orly wrote: ZeXx86 wrote: By default channel mapping with SRXL2 will require very likely no or almost no changes. So it should be plug and play, unless you will completely change radio profile. So default settings = will work immediately. Onyl SRXL2 should be selected and Throttle channel assigned in the Channels window. Sorry, the term in my mind should be ESC, becasue that stick controls two functions, motor and pitch My ESC is plugged into AUX1, I followed the instructions, but 1) In the software it shows as unassigned, AND 2) IF I try to assign throttle to something - AUX1 is NOT an option in the drop down list So? Thanks is because in the spirit software, you are assigning the function of the spirit to the TX channel not vice-versa so in the spirit for the throttle, you just have to select channel 1 then go in diagnostic and see if moving throttle stick, make move the throttle indicator |
|
| Author: | alex4orly [ Thu 09. Jul 2020 9:11:03 ] |
| Post subject: | Re: Setup serial satellite 4651T |
urgno wrote: OT want to point out that I am correctly receiving the reply notification /OT alex4orly wrote: ZeXx86 wrote: By default channel mapping with SRXL2 will require very likely no or almost no changes. So it should be plug and play, unless you will completely change radio profile. So default settings = will work immediately. Onyl SRXL2 should be selected and Throttle channel assigned in the Channels window. Sorry, the term in my mind should be ESC, becasue that stick controls two functions, motor and pitch My ESC is plugged into AUX1, I followed the instructions, but 1) In the software it shows as unassigned, AND 2) IF I try to assign throttle to something - AUX1 is NOT an option in the drop down list So? Thanks is because in the spirit software, you are assigning the function of the spirit to the TX channel not vice-versa so in the spirit for the throttle, you just have to select channel 1 then go in diagnostic and see if moving throttle stick, make move the throttle indicator All good Thanks |
|
| Page 1 of 1 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|