|
It is currently Fri 22. Nov 2024 6:48:57
|
View unanswered posts | View active topics
| Author |
Message |
|
Jman841
|
 Posted: Wed 05. Nov 2014 16:08:17 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Tomas,
One quark I have noticed with the new software is when I assign bank switching to channel 7 using futaba sbus, after it asks me to save, I click yes, and all the servo's go crazy spazming back and fourth until i turn it off and back on again. Once I reset it, all is good and settings were saved, however, I am not sure why it does this when saving changed settings to the unit sometimes.
|
|
| Top |
|
 |
|
Jman841
|
Posted: Wed 05. Nov 2014 16:12:26 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
This also happened when I opened the log.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Wed 05. Nov 2014 19:22:28 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Thank you very much for the report.
This is not good, do you have throttle channel assigned?
_________________
Spirit System developer
|
|
| Top |
|
|
|
Jman841
|
Posted: Wed 05. Nov 2014 23:11:52 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
On my Gaui X3 I do. Throttle channel is assigned to Channel 1.
On my G570 I do not as I use the channel where it would go to power it and throttle is directly into the Rx.
Both have had this happen. Fortunately it causes no damage and the unit saves properly and all is normal after I reboot the spirit.
|
|
| Top |
|
|
|
Jman841
|
Posted: Thu 06. Nov 2014 1:49:47 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
This happens anytime I save or pull the logs from the unit on the X3. The Scary part is since the throttle is controlled through the FBL it starts to spin the blades up. Luckily it doesn't stay on and only moves them a little bit, but, that is definitely a concern.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 06. Nov 2014 8:28:15 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Sorry to hear about your issue, unfortunately I can't reproduce it,
but I will investigate where could be a problem.
Do you have assigned channel for Throttle in both units?
What RX/TX do you use?
Could you send me/attach your settings, please?
_________________
Spirit System developer
|
|
| Top |
|
|
|
elfew
|
Posted: Thu 06. Nov 2014 8:48:56 |
|
Joined: Sun 25. Aug 2013 9:14:16
Posts: 226
|
|
I had same issue but with v24 when I opened a log
_________________
DX9 - Chase 360 - Spirit
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 06. Nov 2014 10:01:32 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
| Top |
|
|
|
Jman841
|
Posted: Thu 06. Nov 2014 13:15:27 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Absolutely, will do.
I'll make a video as well. Thanks for the excellent support!
|
|
| Top |
|
|
|
Jman841
|
Posted: Thu 06. Nov 2014 13:19:28 |
|
Joined: Thu 31. Jul 2014 21:27:22
Posts: 215
|
|
Here is my current file for the Gaui X3 with X4r frsky rx, Tarot S.bus adatper, Hobbywing 50 amp V3, and Taranis Plus Tx.
I am using a Lenovo Laptop running window's 8.1
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: Bing [Bot] and 31 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
