| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-E https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3375 |
Page 1 of 1 |
| Author: | pidder [ Tue 02. Jul 2019 14:17:01 ] |
| Post subject: | Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-E |
Hi, my question is regarding the above metioned setup. I use UniSens-E (under Graupner HOTT as GAM)to detect the used capacity and let the receiver tell me by using a switch. Now - with the sprirt unit i have to decide whether i will use telemetry port for spirit setup or to use the UniSens-E unit. My question: Is there any possible wireing to have both functions possible via the telemtry port?  regards Peter |
|
| Author: | TomasN [ Tue 02. Jul 2019 16:24:26 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
Yes, you can use Y-cable. But before connecting of both components you have to set UnisensE or Spirit to EAM mode instead of GAM. |
|
| Author: | TomasN [ Tue 02. Jul 2019 16:27:43 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit |
|
| Author: | pidder [ Thu 04. Jul 2019 19:38:23 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
TomasN wrote: See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit this - i will try this - but what about the wires? The unisons needs the red cable for power-supply. It is recommended that on the SYS-port of the spirit the must not be any voltage!!! Did you cut the red wire or is it no problem? |
|
| Author: | TomasN [ Thu 04. Jul 2019 20:04:31 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable. Attachment: wiring.png [ 11.38 KiB | Viewed 801 times ] |
|
| Author: | pidder [ Fri 05. Jul 2019 7:06:00 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
TomasN wrote: Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable. Attachment: wiring.png Thank you very much - i will try this!!! |
|
| Author: | pidder [ Sun 14. Jul 2019 7:59:12 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
TomasN wrote: Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable. Attachment: wiring.png I tried this an it works!!!!!  Great job thank you very much for your help! Regards Peter |
|
| Author: | enied [ Fri 28. Feb 2020 11:02:29 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
TomasN wrote: Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable. Attachment: wiring.png Hi TomasN, does it harm to connect GND ? Currently I have connected it and it works. Thank you in advance for your feedback. Best, Eugen |
|
| Author: | TomasN [ Fri 28. Feb 2020 12:03:40 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
Connecting also GND is ok . But single signal wire is enough and simplier. |
|
| Author: | enied [ Fri 28. Feb 2020 12:30:04 ] |
| Post subject: | Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens- |
Thank you ! |
|
| Page 1 of 1 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|