| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Rpm data are too noisy issue https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3133 |
Page 1 of 2 |
| Author: | matty609 [ Sun 03. Feb 2019 18:14:44 ] |
| Post subject: | Rpm data are too noisy issue |
Hi guys, I have already read the manual which says that I need to protect the wiring by adding a ferrite, which I did already. The esc is castle 120hv and I am using a spirit pro. The model is a goblin 570. What Can I do for fix that? Also..I f I should fly with that error, will cause a crash during the flight or it doesn't affect it? I am scared to fly in this condition. p.s. sensor filter is already set to 8. thank you |
|
| Author: | ZeXx86 [ Sun 03. Feb 2019 23:11:12 ] |
| Post subject: | Re: Rpm data are too noisy issue |
Hi, the problem could be caused by too high value of the Governor Response. Could you try to decrease it in the Governor settings? |
|
| Author: | matty609 [ Mon 04. Feb 2019 7:25:00 ] |
| Post subject: | Re: Rpm data are too noisy issue |
Hi thomas! Ican tey to decrease it. How many points? Thank you! |
|
| Author: | ZeXx86 [ Mon 04. Feb 2019 8:24:10 ] |
| Post subject: | Re: Rpm data are too noisy issue |
It depends on if you were changing the value in some way from default configuration. But you can try to set it to value of 4. |
|
| Author: | matty609 [ Mon 04. Feb 2019 20:48:39 ] |
| Post subject: | Re: Rpm data are too noisy issue |
Hi Thomas, my value was 5 and I decreased it to 4. nothing seems changed though. Any other suddgestion? here is the log  Also...I have noticed that request rpm are a little bit different from current rpm, especially in idle up 1. IDLE1: request 2072, current 2300 IDLE2:request 2300, current 2400 IDLE3: request 2600, current 2600 thank you! |
|
| Author: | matty609 [ Thu 07. Feb 2019 17:33:01 ] |
| Post subject: | Re: Rpm data are too noisy issue |
none has my same issue? |
|
| Author: | matty609 [ Thu 07. Feb 2019 22:22:05 ] | ||
| Post subject: | Re: Rpm data are too noisy issue | ||
Hi guys, to day I removed the tail boom and tried to move the yellow wire by the other side..nothing changed tho here is the vlog and few pics...that I hope could helping me resolve this issue  
|
|||
| Author: | ZeXx86 [ Thu 07. Feb 2019 22:29:47 ] |
| Post subject: | Re: Rpm data are too noisy issue |
Hello, you should never use higher frequency for Castle ESC than 60Hz. This can cause big troubles. Are you using Castle ESC Telemetry? |
|
| Author: | matty609 [ Thu 07. Feb 2019 22:43:26 ] |
| Post subject: | Re: Rpm data are too noisy issue |
No, I am not using it |
|
| Author: | matty609 [ Thu 07. Feb 2019 22:47:03 ] |
| Post subject: | Re: Rpm data are too noisy issue |
Throttle frequency To achieve the fastest governor reaction it is necessary to set the highest possible frequency. For ESC it could be only 60Hz, but mostly all can work even with 200Hz. If you are unsure, please contact manufacturer of the ESC. For combustion helicopters it is max. operating frequency of the throttle servo. That’s why I put 200.. |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
