|
It is currently Mon 25. Nov 2024 0:25:02
|
View unanswered posts | View active topics
| Author |
Message |
|
Matzer27
|
 Posted: Tue 13. Nov 2018 13:46:15 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
I just changed from the Vstabi to the spirit pro. On the Vstabi everything was normal. With the spirit pro my tail wags violently and sometimes it kicks by about 30 deg.
My setup:
Tail-servo: Align DS650
Hobbywing Platinum HV 160 with 1700 rpm
Gain: started with 50 % and tried down to 0 and up to 100 %
Rudder 1520micros 333Hz
Rudder Common Gain 1.30x
Rotation speed Rudder 9
Rudder delay 5
Rudder dynamic 7
What is wrong on my setup?
Last edited by Matzer27 on Wed 14. Nov 2018 9:44:30, edited 1 time in total.
|
|
| Top |
|
 |
|
eg183100
|
Posted: Tue 13. Nov 2018 14:19:11 |
|
Joined: Tue 09. Oct 2018 12:31:17
Posts: 29
|
|
I would set common gain to 1.0
Could you post your setup. As with gyro at 0%. You should see a difference;-)
|
|
| Top |
|
|
|
Matzer27
|
Posted: Tue 13. Nov 2018 15:57:57 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
Here the Telemetry logs of the gain and the Ruder.
| Attachments: |
Screenshot 2018-11-13 15.56.24.png [ 45.38 KiB | Viewed 647 times ]
|
Last edited by Matzer27 on Wed 14. Nov 2018 9:44:53, edited 2 times in total.
|
|
| Top |
|
|
|
Matzer27
|
Posted: Tue 13. Nov 2018 16:02:58 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
And here the Ruder
| Attachments: |
Screenshot 2018-11-13 16.01.18.png [ 42.71 KiB | Viewed 646 times ]
|
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 15. Nov 2018 9:11:04 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Hello,
I recommend to set Rudder delay to 0. Then we dont know anything about rest of your settings. Could you attach your settings file (4ds) here, please?
Very likely the problem could be in Pirouette Consistency settings value.
When looking at the Diagnostic tab in the Spirit Settings, can you see that the Gain is really changing and reacting to your radio?
_________________
Spirit System developer
|
|
| Top |
|
|
|
Matzer27
|
Posted: Thu 15. Nov 2018 12:16:58 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
| Top |
|
|
|
Matzer27
|
Posted: Thu 15. Nov 2018 12:25:29 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
In the diagnostic tab I see the Gyro is moving from 0% up to +100% when a change it in the tx with a poti. I want only HH.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 15. Nov 2018 12:30:49 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Thank you for the settings.
For Spirit unit it would be better to set servo arm one hole further from the center.
Then you can set Rudder Delay to 0. Gyro Gain can be configured to be around 50% for the beginning.
Performance should be better after these changes.
Do you remember if you used a Revomix with VBar?
_________________
Spirit System developer
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Thu 15. Nov 2018 12:44:36 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
After changing hole in the servo arm please do not forget to decrease Rudder end-points. They will be smaller now.
_________________
Spirit System developer
|
|
| Top |
|
|
|
Matzer27
|
Posted: Thu 15. Nov 2018 12:49:31 |
|
Joined: Tue 01. May 2018 15:26:53
Posts: 10
|
|
I didn´t used a revomix with VBar.
For the servo arm I already using the far end hole of it.
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: No registered users and 72 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
