Spirit System
https://www.spirit-system.com/phpBB3/

[Solved]Spirit Governor
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2575		 Page 1 of 2
Author:  demon450 [ Tue 29. May 2018 15:30:17 ]
Post subject:  [Solved]Spirit Governor
I'm using Jeti DS14 with Spirit Pro on my Goblin380. The ESC is HW60A V4. The motor is HK3020.
I set the divider to 5 which is 10/2 and gear ratio to 5.7 = 120/21
I enabled the Governor and using a standard TH curve just for testing purpose, I set the max RPM to 3200 but it reaches 3200 when the TH stick is at 50%. When the TH goes to 60% it reaches 4000 rpm and still increasing slowly.
Not sure what I'm doing wrong...

HK3020 specs: https://www.scorpionsystem.com/catalog/ ... 3020_1000/
Author:  delta peak [ Tue 29. May 2018 16:37:49 ]
Post subject:  Re: Spirit Governor
Did you connect the ESC to Spirit?
Author:  demon450 [ Tue 29. May 2018 16:51:09 ]
Post subject:  Re: Spirit Governor
delta peak wrote:
Did you connect the ESC to Spirit?


Yes, I followed the HW telemetry guide and wired properly and I can see the RPM in the main screen.
Author:  delta peak [ Tue 29. May 2018 17:19:20 ]
Post subject:  Re: Spirit Governor
Max rpm in Spirit settings means the max rpm you will get at 100% throttle. In your case approx. 4000rpm. So when e.g. the curve is set to 75% you get 3000rpm.
You might want to set max rpm to 3600.
Author:  ZeXx86 [ Tue 29. May 2018 18:06:47 ]
Post subject:  Re: Spirit Governor
Hello,

when you open the software and go to the Governor/Throttle, what requested RPM you can see there?
Requested RPM should be approximately equal with Current RPM once the motor is spooled up.
Author:  demon450 [ Wed 30. May 2018 1:45:26 ]
Post subject:  Re: Spirit Governor
ZeXx86 wrote:
Hello,

when you open the software and go to the Governor/Throttle, what requested RPM you can see there?
Requested RPM should be approximately equal with Current RPM once the motor is spooled up.


They are both 0, but if I click the tester, the RPM shows up the same number as in Transmitter.

Attachments:
Capture.PNG
Capture.PNG [ 25.43 KiB | Viewed 683 times ]
Author:  demon450 [ Wed 30. May 2018 15:07:35 ]
Post subject:  Re: Spirit Governor
I checked the log, "Governor engaged" is not showing up.
I also tried to uncheck the governor and I got the linear RPM, whenever I stop moving the stick, the RPM stays. If I check the governor, the RPM will keep increasing even I stop moving the stick.
The HW60A V4 is set to linear throttle.
Author:  ZeXx86 [ Wed 30. May 2018 15:22:07 ]
Post subject:  Re: Spirit Governor
That is quite strange - you have to see a Requested RPM in the Governor window when you will set a throttle curve above 50%.
If it is under, then it will be zero.
I recommend to use a flat throttle curve.

Is the governor enabled in all banks (if banks are enabled)?
Author:  demon450 [ Wed 30. May 2018 15:35:50 ]
Post subject:  Re: Spirit Governor
ZeXx86 wrote:
That is quite strange - you have to see a Requested RPM in the Governor window when you will set a throttle curve above 50%.
If it is under, then it will be zero.
I recommend to use a flat throttle curve.

Is the governor enabled in all banks (if banks are enabled)?


Ok, I will try a flat curve at 70%.
No, but I only have 1 bank configured(bank 0) and only use this bank.
Author:  demon450 [ Wed 30. May 2018 22:42:02 ]
Post subject:  Re: Spirit Governor
This time I got the requested RPM shows up, and the value looks good.
But the current RPM is always 0, if I click tester, I can see the current RPM and it still showing up on transmitter screen.
I checked the log, still no "Governor engaged" shows up.
Page 1 of 2 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/