It is currently Sun 24. Nov 2024 14:38:09

All times are UTC + 1 hour





Post new topic Reply to topic  [ 19 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
PostPosted: Wed 02. May 2018 8:40:28 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Hello, I am sorry I do not speak English I use a translator.
I concerns is; I have Spirit (red and black), I went up on a copter with an ESC DC 160 HV, the controller and the module are recognized by the radio JETI DC 16, the telemetry does not work, just the % of vibrations.


Top
 Profile  
 
PostPosted: Wed 02. May 2018 8:49:51 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Hello,

do you have CC Telem cable?

Please check this guide:
http://manual.spirit-system.com/index.p ... _Telemetry

There you can see all steps that are needed to make it work.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Wed 02. May 2018 8:55:56 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Thank you for this fast answer, everything was make as on the link, but there is no telemetry, the resistance of 10k was welded.
THE ESC is recognized, and works, when I put the son with resistance if I cut the RX without removing lipos, the engine turns(shoots) 2 seconds.

Image

Image

Image

Image

Image

Image

Image


Top
 Profile  
 
PostPosted: Wed 02. May 2018 12:40:11 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Version
Spirit 2.3.4
ESC 4.25


Attachments:
test700.zip [257 Bytes]
Downloaded 22 times
Top
 Profile  
 
PostPosted: Wed 02. May 2018 14:39:08 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
So the ESC is working also with modified cable (with 10kOhm resistor) - you can control the throttle, right?

It is important that it is working well.

Can you tell me what ESC do you exactly have?

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Wed 02. May 2018 15:35:20 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Mode 1 gaz à droite
ESC castle créations Phenix edge HV 160
Even with cable him 10k the ESC does not arm itself, orders it gases is settled in at the end of race 87 % 99 %.


Top
 Profile  
 
PostPosted: Wed 02. May 2018 15:44:02 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Did you configured Throttle Range according the manual?

See this page:
http://manual.spirit-system.com/index.p ... Castle_ESC

If not, then ESC will not initialize at all. Castle ESCs require different throttle range than other ESCs.

Also please note, that with Link-Live feature in the ESC it can work only with 10KOhm resistor.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Wed 02. May 2018 16:14:54 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Gaz +100% - 100%

test A:
ESC > link live = disabled
no R10K
Spirit > telemetrie setting = Disabled
Jeti > Spirit > télémétrie setting > Disabled
moteur Ok
I have branch White wire RPM output Signal (PIT pine), return on screen JETI > RPM = 0

test B:
ESC > link live = enabled
R10K Between + and signal
Spirit > telemetry setting = Castle créations & Talon
Jeti > Spirit > télémétrie setting > Castle création & Talon
moteur Not Ok Not initialized

I have redo test with an ESC PHOENIX EDGE 120 HV, test A or B identical results


Top
 Profile  
 
PostPosted: Wed 02. May 2018 19:24:55 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Thank you for the details.

Do you use an external BEC?
Unfortunately the only problem that I am thinking about is in the cable with 10kOhm resistor.

Did you tried it with your other unit too?

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Wed 02. May 2018 19:36:16 
Offline

Joined: Wed 02. May 2018 7:33:33
Posts: 81
Thank you to take into account my concerns.
No I use 2 lipos batteries with an electronic inter.
I commanded you a cordon R10k in the doubt of my cordon but I think of being on my assembly.
I have to receive ASAP
With the ESC 120 or 160 identical results.

Assembly prototype, negative result, the ESC does not arm, the engine does not work.

Image


Last edited by passe partout on Wed 02. May 2018 19:59:36, edited 3 times in total.

Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 19 posts ]  Go to page 1, 2  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: Bing [Bot], mainstreet and 56 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .