|
It is currently Sun 24. Nov 2024 15:05:39
|
View unanswered posts | View active topics
 
|
Page 1 of 1
|
[ 6 posts ] |
|
| Author |
Message |
|
keeny
|
 Posted: Tue 06. Mar 2018 20:17:02 |
|
Joined: Tue 17. May 2016 9:19:20
Posts: 56
|
|
Been away for a short while anyways on my 500 align heli when I plug the batt in it goes nuts for a couple of seconds and then stops...then initializes like normal.
I have recently replaced like for like servo..... any ideas?
Cheers, Chris.
Last edited by keeny on Tue 13. Mar 2018 19:54:33, edited 1 time in total.
|
|
| Top |
|
 |
|
ZeXx86
|
Posted: Tue 06. Mar 2018 20:37:58 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Hello,
it look like some BEC related issue.
Could you disconnect all servos (and anything that is not necessary) and try it again?
_________________
Spirit System developer
|
|
| Top |
|
|
|
keeny
|
Posted: Wed 07. Mar 2018 16:00:04 |
|
Joined: Tue 17. May 2016 9:19:20
Posts: 56
|
|
Thanks for the reply. I disconnected all the servos then plugged in one at a time which resulted in an initial short movement then the up and down bit, the last servo which is a new replacement dipped down when the others went up when first plugging in the battery. then when I do bailout in quick succession it bounces very quickly at each limit up and down. could this be a problem with the new servo or have I missed some setting.
I didn't change any settings as the servo is an exact replacement and even centres in the exact same place.
Cheers, Chris.
ps, all the movements and bailout are going the correct way.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Wed 07. Mar 2018 22:47:12 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Unfortunately it look like a servo issue. This should really not happen at any moment.
I guess that it is causing a short during these events and probably BEC is restarting as safety protection.
The only servos we have experience that were doing a very similar things were from BK.
_________________
Spirit System developer
|
|
| Top |
|
|
|
keeny
|
Posted: Tue 13. Mar 2018 19:53:23 |
|
Joined: Tue 17. May 2016 9:19:20
Posts: 56
|
|
Finally got around to stripping new align servo down and there was a grumpy gear in there that you couldn't really feel when assembled.
Changed the gear and all is well.
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Wed 14. Mar 2018 10:29:54 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Thank you for great message!
Good to know it is working well now.
_________________
Spirit System developer
|
|
| Top |
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
 |
Who is online |
 |
Users browsing this forum: 10x and 53 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
