Spirit System
https://www.spirit-system.com/phpBB3/

[SOLVED] Set up SPIRIT PRO
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2365		 Page 1 of 1
Author:  MOREAU [ Mon 01. Jan 2018 12:53:07 ]
Post subject:  [SOLVED] Set up SPIRIT PRO
Hello,

After installation Spirit Pro on my TREX 500 / TX Futaba T8FG / Rx Futaba R617FS , when I check "channels" with Spirit Settings v2.4.3 on my computer , the screen is different with your of Spirit System Manual !
Indicator of Throttle is green on a half and i have "unassigned" for channel ?
Indicator of Pitch is green on 1/4 ?
Is this normal ?

Regards

Many thanks for your product and Happy New Year 2018

Attachments:
File comment: view FUTABA T8FG at the same time
IMG_2749.JPG
IMG_2749.JPG [ 710.58 KiB | Viewed 838 times ]
IMG_2748.JPG
IMG_2748.JPG [ 666.46 KiB | Viewed 838 times ]
Author:  ZeXx86 [ Mon 01. Jan 2018 16:05:49 ]
Post subject:  Re: Set up SPIRIT PRO
Hello,

you are using PWM connection which needs little bit more adjustments in the radio.
You may need to modify Travel Adjust to obtain +/- 100% on all channels.

Is the Pitch channel moving when you are moving with Pitch stick?

Throttle is unassigned, because it is not transffered by the cables. So only receiver is seeing the value. Unit does not care about throttle with PWM connection since the ESC is connected to the receiver.

Happy New Year too!
Author:  MOREAU [ Mon 01. Jan 2018 20:57:43 ]
Post subject:  Re: Set up SPIRIT PRO
Hello

Many thanks for the quick answer !

The Pitch channel is moving when I am moving with Pitch stick / see 2 pictures

More 2 pictures on diagnostic with Pitch stick on 100% and more Pitch stick on 0%

Regards

Attachments:
File comment: diagnostic when pitch stick 100%
IMG_2762.JPG
IMG_2762.JPG [ 451.71 KiB | Viewed 790 times ]
File comment: Futaba Pitch stick 100 %
IMG_2761.JPG
IMG_2761.JPG [ 332.11 KiB | Viewed 790 times ]
File comment: Pitch stick 100%
IMG_2760.JPG
IMG_2760.JPG [ 338.18 KiB | Viewed 790 times ]
Author:  MOREAU [ Mon 01. Jan 2018 21:01:01 ]
Post subject:  Re: Set up SPIRIT PRO
Hello
second view
Regards

Attachments:
File comment: dignostic with pitch stick on 0%
IMG_2763.JPG
IMG_2763.JPG [ 474.89 KiB | Viewed 790 times ]
Author:  ZeXx86 [ Tue 02. Jan 2018 8:27:54 ]
Post subject:  Re: Set up SPIRIT PRO
Thank you!

Please check in your radio that the pitch channel is going all the way from -100 to 100%. There could be some curve configured in.
The easiest way to verify it is to check SERVO menu in the radio. Then move with the Pitch stick.

Also note, that each power up, the unit is detecting centering signal. If aileron, elevator or rudder sticks are not in the center, then the center will be off for the pitch channel.
But still there is issue with the small range, so I think that it is all caused by some pitch curve in the radio.
Author:  MOREAU [ Tue 02. Jan 2018 9:26:18 ]
Post subject:  Re: Set up SPIRIT PRO
Hi,

OK
I change the configuration in my FUTABA / Model TYPE / SWASH H-1 and not SWASH HR3
Now on "SERVO" I have : 100% and -100% for pitch stick :D

I continue my set up

Many Thanks ;)

Regards
Author:  ZeXx86 [ Tue 02. Jan 2018 9:43:18 ]
Post subject:  Re: Set up SPIRIT PRO
Perfect, you are welcome!
Author:  MOREAU [ Tue 02. Jan 2018 10:45:23 ]
Post subject:  Re: [SOLVED] Set up SPIRIT PRO
Hi,

last thing before to fly

after all settings on my Futaba T8FG like your "set up guide for Futaba"

On diagnostic :
Giro / normal condition 68%
Giro / SH button ON / 63% ("Rescue" appears)
Is it the right setting ? why not 60% and -60% for rescue ?

Regards

Attachments:
IMG_2776.JPG
IMG_2776.JPG [ 579.55 KiB | Viewed 771 times ]
IMG_2775.JPG
IMG_2775.JPG [ 628.85 KiB | Viewed 771 times ]
Page 1 of 1 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/