Connection for Integration and Telemetry.
See the OpenTX integration guide for more info:
http://manual.spirit-system.com/index.p ... ntegration
| Attachments: |
|
uspirit-frskyxsr.png [ 206.42 KiB | Viewed 8138 times ] |
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| FrSky XSR and uSpirit - Connection https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2254 |
Page 1 of 2 |
| Author: | ZeXx86 [ Tue 03. Oct 2017 11:04:27 ] | ||
| Post subject: | FrSky XSR and uSpirit - Connection | ||
Connection for Integration and Telemetry. See the OpenTX integration guide for more info: http://manual.spirit-system.com/index.p ... ntegration
|
|||
| Author: | xoexoe [ Fri 21. Jun 2019 20:49:57 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
Looks like I would need some type of Y-cable to make this work, but the picture on the purchase website only shows a regular two-sided cable. If I select the µSpirit version of the FrSky Integration cable, will it come with the y-harness thing? Here is the picture I'm talking about:  How would I make connections from the 4 pins of the XSR to the two separate 3x1 housings of the µSpirit unit? Also, the diagram in post #1 here should be in the Wiki manual! Seems important. |
|
| Author: | ZeXx86 [ Mon 24. Jun 2019 7:30:57 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
You have to solder the cables together. It is recommended only for experienced pilots. |
|
| Author: | xoexoe [ Tue 25. Jun 2019 7:24:11 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
Thanks. Makes sense. Also, is it possible to create my own FrSky integration cable? Can I just connect the correct pins together with a direct wire or are there electronics/logic/resistors/etc under the heat shrink? |
|
| Author: | ZeXx86 [ Tue 02. Jul 2019 8:44:44 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
No, you can't create own. It contain electronics. |
|
| Author: | jjuk [ Sun 14. Jul 2019 17:57:54 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
Cut the plug off the sbus cable and solder it to the xsr. |
|
| Author: | ZeXx86 [ Wed 17. Jul 2019 17:34:00 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
S-Bus Adapter and FrSky integration cable are very different inside. So you can't swap each other even if end plugs are same. |
|
| Author: | jjuk [ Wed 17. Jul 2019 19:24:36 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
Whoops my bad! Any plans for f.port support? Sbus and telemetry on one pin! |
|
| Author: | Mikej [ Thu 26. Dec 2019 12:25:31 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
See below - my mistake |
|
| Author: | Mikej [ Thu 26. Dec 2019 12:34:53 ] |
| Post subject: | Re: FrSky XSR and uSpirit - Connection |
Sorry - ended up answering the wrong thread 
|
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|