| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Henseleit TDF setup to start with https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2214 |
Page 1 of 3 |
| Author: | guido [ Fri 08. Sep 2017 20:24:08 ] |
| Post subject: | Henseleit TDF setup to start with |
Hi, I'm looking forward to get my Henseleit TDF in a couple of weeks. I'm wondering which setup I should use to start with, because there is no TDF default setup available in the wizard. Do I need to change some specific values because of the linear servo drive? Thanks Guido |
|
| Author: | ZeXx86 [ Sun 10. Sep 2017 11:29:47 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Hi, you can use TDR profile or Default. Increase Pirouette Consistency to at least 170. Optimal will be probably 175 - 180. |
|
| Author: | guido [ Mon 11. Sep 2017 9:36:51 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Hi, Thanks. I will start with these settings. Guido |
|
| Author: | Franky13 [ Mon 09. Oct 2017 7:14:37 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Hi! There are already new insights for the setup TDF? Thanks! |
|
| Author: | ZeXx86 [ Mon 09. Oct 2017 7:18:15 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Hi, for linear servos I just recommend to decrease Geometry 6° by approx. 25% since overall gain is too high. This mean that what you will find as a correct value should be then decreased (*0.75). But all other parameters are similar to other models. |
|
| Author: | Franky13 [ Sun 15. Oct 2017 12:09:51 ] | ||
| Post subject: | Re: Henseleit TDF setup to start with | ||
Hello! How do I get the rear set nicely? I have already set the values very high. Can I still higher? I'm not quite satisfied with the rear. It turns a little to the right and at the same time downwards. Although little, but it could be better! My file I have attached! Thank you!
|
|||
| Author: | ZeXx86 [ Sun 15. Oct 2017 12:44:53 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Hello, what is rear? Is it the rudder? If yes, have you Gyro Gain configured to work in Head Lock mode? This can be visible in the Diagnostic tab. |
|
| Author: | Franky13 [ Sun 15. Oct 2017 15:07:23 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Yes, of course I meant the rudder  I set the values in the transmitter! In the transmitter I already idle 1 - 75%, idle 2 - 65% and idle 3 - 60%! |
|
| Author: | ZeXx86 [ Sun 15. Oct 2017 15:26:12 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
That is good, but it still does not mean that rudder will be in Head Lock mode. For example if you have Futaba, then there could be NORM mode which will set it for Normal mode. And you want Head Lock. Please check Diagnostic tab as I have written earlier, only there you will see the mode that will be really used. |
|
| Author: | Franky13 [ Sun 15. Oct 2017 15:36:15 ] |
| Post subject: | Re: Henseleit TDF setup to start with |
Ok, it is Head Lock! Rudder Servo is Futaba BLS276 |
|
| Page 1 of 3 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
