Yes, you can.
There is nearly no difference in the configuration.
But we will add the preset in the upcoming version
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Goblin Fireball https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2147 |
Page 1 of 2 |
| Author: | lostmyheli [ Thu 10. Aug 2017 15:11:18 ] |
| Post subject: | Goblin Fireball |
There is no file in the Model Presets for the Goblin Fireball. Should I use the default or maybe the Goblin 380 ? Thanks |
|
| Author: | ZeXx86 [ Thu 10. Aug 2017 15:31:01 ] |
| Post subject: | Re: Goblin Fireball |
Yes, you can. There is nearly no difference in the configuration. But we will add the preset in the upcoming version
|
|
| Author: | gerry [ Thu 10. Aug 2017 18:45:47 ] |
| Post subject: | Re: Goblin Fireball |
The Hobby Wing controller in the Fireball has an RPM output.Can I infect the Spirit or comes the speed of the Uni cable? How can I adjust the 24 poles of the motor? LG Gernot |
|
| Author: | lostmyheli [ Sat 12. Aug 2017 20:05:32 ] | ||||
| Post subject: | Re: Goblin Fireball | ||||
Brand new Fireball with Tail Wag can't get rid of it. Tail gain down to 30% can I go any lower ? Any high I get fast wag in Idle Up 3 Setup files attached. Will do vibration logs later today. Any suggestions ? Thanks
|
|||||
| Author: | ZeXx86 [ Sat 12. Aug 2017 20:14:52 ] |
| Post subject: | Re: Goblin Fireball |
What tail servo do you have? Probably you will need to set Rudder Delay (decrease). Reducing Pirouette Consistency to 150 can improve it too. It is also usual that new goblin kits needs "smoothening" of the tail mechanics since in certain angles it is not moving freely. Only then tail mechanics will perform well. Very often it is sorted by itself according the pilots after couple of flights. Very important is that each ball joint is moving with absolutely no friction and there is no point that is causing additional slow down. Tail gain should be around at least 50%, but it is also very dependent on the servo. |
|
| Author: | lostmyheli [ Sat 12. Aug 2017 20:20:55 ] |
| Post subject: | Re: Goblin Fireball |
Using the stock DS12T servo. I'll make those changes along with striping down the tail and check it smoothness. Report back tomorrow if it improves. |
|
| Author: | ZeXx86 [ Sat 12. Aug 2017 20:42:50 ] |
| Post subject: | Re: Goblin Fireball |
For this servo I recommend to set Rudder Delay to 0. |
|
| Author: | lostmyheli [ Sun 13. Aug 2017 19:37:33 ] | ||||
| Post subject: | Re: Goblin Fireball | ||||
Piro consistency set to 150, Rudder delay set to 0. Tore down the tail assembly polished and oiled the tail shaft. Tail gain at 50% seems better at lower head speed but at higher head speed still getting the fast wag. Reduce the gain to get rid of fast wag but then have slow wag at lower head speed. I don't see any vibration issues, logs attached. Have any other suggestions ?
|
|||||
| Author: | Trek nut [ Mon 14. Aug 2017 2:01:51 ] |
| Post subject: | Re: Goblin Fireball |
just sorted my out , check the tail boom and frame make sure they are tight , and thurst bearing on tail with the smaller diameter out . same problem with my . it wasn t the spirit . good luck |
|
| Author: | Butscher [ Sat 03. Feb 2018 17:28:08 ] |
| Post subject: | Re: Goblin Fireball |
I have the same problem with commuting fast tail. The tail is smooth running. Servos are standard sab. |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
