Spirit System • View topic

It is currently Mon 25. Nov 2024 4:56:00

View unanswered posts | View active topics

Board index » English » HELI » Support

All times are UTC + 1 hour

Jeti

Page 1 of 2

[ 16 posts ]

Go to page 1, 2 Next

Print view

Previous topic | Next topic

Author

Message

Ktm250

Post subject: Jeti

Posted: Tue 20. Jun 2017 21:58:31

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

I just tried getting my telem working on my Jeti. After going through the set up as per the wilki page, my Jeti will not see the telem Any thoughts.
Thanks

Last edited by Ktm250 on Wed 12. Sep 2018 0:13:24, edited 4 times in total.

Top

ZeXx86

Post subject: Re: Telem CC Cable Causes Low Voltage

Posted: Tue 20. Jun 2017 22:02:55

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Hello,

you have to enable Link-Live feature in your ESC to make it work (and also to enable Telemetry in the Spirit Settings)
It should not suck any voltage normally, otherwise it would be very hot.
Is the Link-Live enabled?

_________________
Spirit System developer

Top

Ktm250

Post subject: Jeti

Posted: Tue 20. Jun 2017 22:42:30

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

Yes it is enabled in the esc and spirit unit.

Last edited by Ktm250 on Tue 11. Sep 2018 23:50:25, edited 2 times in total.

Top

Ktm250

Post subject: Jeti

Posted: Tue 20. Jun 2017 23:22:59

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

Any thoughts.

Last edited by Ktm250 on Tue 11. Sep 2018 23:50:49, edited 2 times in total.

Top

ZeXx86

Post subject: Re: Telem CC Cable Causes Low Voltage

Posted: Wed 21. Jun 2017 7:06:10

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Can you try to decrease the BEC voltage to 6.6V too (just for try)?
In any way it is really strange. Is your wiring special in some way?
Are you using external BEC, buffer pack or similar electronics?

Do you have a multimeter? If so, you can measure resistance between the wires - when the cable is disconnected. Between signal and red wire, there should be 1kOhm. Between other, there should be nothing.

_________________
Spirit System developer

Top

Ktm250

Post subject: Jeti

Posted: Wed 21. Jun 2017 22:40:24

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

Nothing special as far as wiring goes. Using jeti x bus with a Rex 7 receiver and jeti muli 6s Lipo telemetry sensor, no external bec or buffer pack. I tested 10k

Last edited by Ktm250 on Tue 11. Sep 2018 23:52:43, edited 1 time in total.

Top

ZeXx86

Post subject: Re: Telem CC Cable Causes Low Voltage

Posted: Thu 22. Jun 2017 7:38:39

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Thanks!
Yes, it should be 10kOhm - sorry for confusion. So the cable is OK fortunately.

So without the cable, when you connect the throttle cable into the AUX port, it is working. With cable it does not work.

Could you try to decrease General - Throttle/Governor - Throttle Range - Min. by 10 - 50us to see if it makes a difference?

Can you check when the unit was bought? Unfortunately some of the very first units have compatibility issue with the CC telemetry. But we are able to fix it for free.

_________________
Spirit System developer

Top

Ktm250

Post subject: Jeti

Posted: Thu 22. Jun 2017 21:46:48

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

I did as you asked and I lowered my min value from 1180 to 1130. Still not working.

Last edited by Ktm250 on Tue 11. Sep 2018 23:54:01, edited 1 time in total.

Top

ZeXx86

Post subject: Re: Telem CC Cable Causes Low Voltage

Posted: Thu 22. Jun 2017 22:15:32

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Please try to decrease the value to 1060us.
In any way it looks like the unit is from the first batch

Have you other unit that was bought few months later?
So that you can try it with a newer unit.

If this will be the case, we can fix the problem in one day and for free. Unfortunately we will need the unit here.

_________________
Spirit System developer

Top

Ktm250

Post subject: Jeti

Posted: Thu 22. Jun 2017 22:51:08

Joined: Sun 02. Nov 2014 18:12:56
Posts: 76

Ok so I lowered it to 1060 and still the same problem.

Last edited by Ktm250 on Tue 11. Sep 2018 23:55:26, edited 1 time in total.

Top

Page 1 of 2

[ 16 posts ]

Go to page 1, 2 Next

Board index » English » HELI » Support

All times are UTC + 1 hour

Who is online

Users browsing this forum: Bing [Bot] and 64 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: