It is currently Sat 23. Nov 2024 23:02:12

All times are UTC + 1 hour





Post new topic Reply to topic  [ 39 posts ]  Go to page 1, 2, 3, 4  Next
  Print view Previous topic | Next topic 
Author Message
PostPosted: Wed 19. Oct 2016 21:20:09 
Offline

Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
:ugeek: Sorry guys I had a melt down and computer crash. Updated to 2.1.
all went wrong then I started medling. I need step by step instructions for Dx8 Ive tried online manual and does not work as I have it
I want bank 0stabilize 1 coaxial 2resque but on the elev d/r switch and resque on the trainer button. I had stab and resue before without bank switching now all in gone.
HELP please. John


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Thu 20. Oct 2016 1:54:42 
Offline

Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
GOT IT. But now all is good except
resue pitch is neg anything above low idel and pitch


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Thu 20. Oct 2016 8:12:00 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Hello,

when you are updating from version 2.0 to 2.1 it should work all out of the box.
If you are updating from version 1 then you have to re-do all the basic settings. The best is to start the Setup Wizard and do everything again, especially Position, Swashplate type, Subtrims, Servo reverses.

There are many changes in the firmware so without doing new configuration, it will not fly well (including wrong rescue).

So the question is, from which version you are updating?
Then we will see where to start.

_________________
Spirit System developer


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Thu 20. Oct 2016 15:49:21 
Offline

Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
I have had them forever,went from 1 to 2 to 2.1 Its on a nitro with spirit pro.


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 7:26:45 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Good, so you were flying with 2.0 previously and everything worked?

If yes, then you only have to update the firmware and software. After this update you do not have to reconfigure Rescue/Stabilisation at all.
When Rescue or Stabilisation is activated, you should see "HF" in the Diagnostic tab. Normally there is "HL" when these modes are not active.
By this you can always verify, if your transmitter configuration is correct.

Gyro gain should be approximately same for the Rescue/Stabilisation as for normal flying.

_________________
Spirit System developer


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 14:57:40 
Offline

Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
All is set up on nitro 600 except to get any possible + pitch in software I have to have % slider all the way to the left, and still only gives 2% = pitch.


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 15:36:19 
Offline

Joined: Sat 02. Jan 2016 12:17:50
Posts: 183
Do you have any subtrim on collective in your radio? If so remove it, set 0 pitch mechanically and it should be ok now.


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 15:47:21 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
In the software/Diagnostic collective pitch bar should go up and down. It is in this way from version 2.

Did you changed Channel mapping in any way in the software?

Maybe you have configured some mixing in your transmitter that changes collective pitch - this is wrong and is not rescue. So I recommend to disable all mixes in your transmitter now.

_________________
Spirit System developer


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 15:50:09 
Offline

Joined: Mon 22. Jun 2015 5:50:05
Posts: 123
No mixes,allmost act as if resque acts on throttle and not collective channels.


Top
 Profile  
 
 Post subject: Re: dazed and confused
PostPosted: Fri 21. Oct 2016 16:05:29 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
Then maybe your collective channel is swapped with throttle.

You can try to modify your throttle curve to see where change will occur.

_________________
Spirit System developer


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 39 posts ]  Go to page 1, 2, 3, 4  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: Bing [Bot] and 59 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .