here it is
| Attachments: |
B0D700.4ds [255 Bytes]
Downloaded 50 times |
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| next gov problem after update 2.1 https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=1663 |
Page 1 of 2 |
| Author: | torro [ Tue 27. Sep 2016 8:51:12 ] |
| Post subject: | next gov problem after update 2.1 |
hi, first, i didn´t change anything, just did the update when gov is enabled, the motor doesn´t start. when gov is disabled, the motor runs immediately after switching the switch. ESC is calibrated, values in spirit are 0 and 100% log is clean any idea? ESC is a YGE160HVK thanks, Flo |
|
| Author: | ZeXx86 [ Tue 27. Sep 2016 9:49:57 ] |
| Post subject: | Re: next gov problem after update 2.1 |
Hi, what will happen if you will wait little bit longer? Was the ESC recalibrated after the update or something else? If completely nothing was changed (except firmware), it should work in the same way as the old firmware. |
|
| Author: | torro [ Tue 27. Sep 2016 10:09:41 ] |
| Post subject: | Re: next gov problem after update 2.1 |
i didn´t change anything! waited 1 minute, nothing. one time, the motor started with gov activated, when i switched to the next bank. throttle value from 64% to 75% |
|
| Author: | torro [ Tue 27. Sep 2016 10:09:57 ] |
| Post subject: | Re: next gov problem after update 2.1 |
but i tried it very often |
|
| Author: | ZeXx86 [ Tue 27. Sep 2016 10:12:49 ] |
| Post subject: | Re: next gov problem after update 2.1 |
Good. Can you please share your settings? At least for Bank 0. |
|
| Author: | torro [ Tue 27. Sep 2016 10:20:24 ] | ||
| Post subject: | Re: next gov problem after update 2.1 | ||
here it is
|
|||
| Author: | guido [ Tue 27. Sep 2016 12:49:19 ] |
| Post subject: | Re: next gov problem after update 2.1 |
Hi, I had the same problem with one of my helis after updating to 2.1. I solved the issue by increasing Spoolup Rampup from 50 to 60µs I hope that solves your issue too. brgds Guido |
|
| Author: | torro [ Tue 27. Sep 2016 14:18:09 ] |
| Post subject: | Re: next gov problem after update 2.1 |
it works. i recalibrated the ESC, same problem. increasing spoolup rampup to 80 was succesfull! |
|
| Author: | thestructured [ Tue 27. Sep 2016 20:30:39 ] |
| Post subject: | Re: next gov problem after update 2.1 |
I had a similar issue on 2.1 where the governor was not engaging at all until I set the spoolup rate to fast |
|
| Author: | ZeXx86 [ Wed 28. Sep 2016 9:23:15 ] |
| Post subject: | Re: next gov problem after update 2.1 |
Thank you for the info. I am glad it works, although it is little bit strange as the starting procedure is very same with previous firmware. Increased spoolup works similarly as when you increase Throttle Range - Min. |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|