|
It is currently Sat 23. Nov 2024 23:08:31
|
View unanswered posts | View active topics
| Author |
Message |
|
torro
|
 Posted: Tue 27. Sep 2016 8:51:12 |
|
Joined: Mon 20. Jun 2016 20:02:31
Posts: 46
|
|
hi,
first, i didn´t change anything, just did the update
when gov is enabled, the motor doesn´t start.
when gov is disabled, the motor runs immediately after switching the switch.
ESC is calibrated, values in spirit are 0 and 100%
log is clean
any idea?
ESC is a YGE160HVK
thanks, Flo
|
|
| Top |
|
 |
|
ZeXx86
|
Posted: Tue 27. Sep 2016 9:49:57 |
|
 |
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Hi,
what will happen if you will wait little bit longer?
Was the ESC recalibrated after the update or something else?
If completely nothing was changed (except firmware), it should work in the same way as the old firmware.
_________________
Spirit System developer
|
|
| Top |
|
|
|
torro
|
Posted: Tue 27. Sep 2016 10:09:41 |
|
Joined: Mon 20. Jun 2016 20:02:31
Posts: 46
|
|
i didn´t change anything!
waited 1 minute, nothing.
one time, the motor started with gov activated, when i switched to the next bank.
throttle value from 64% to 75%
|
|
| Top |
|
|
|
torro
|
Posted: Tue 27. Sep 2016 10:09:57 |
|
Joined: Mon 20. Jun 2016 20:02:31
Posts: 46
|
|
but i tried it very often
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Tue 27. Sep 2016 10:12:49 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Good. Can you please share your settings? At least for Bank 0.
_________________
Spirit System developer
|
|
| Top |
|
|
|
torro
|
Posted: Tue 27. Sep 2016 10:20:24 |
|
Joined: Mon 20. Jun 2016 20:02:31
Posts: 46
|
|
here it is
| Attachments: |
B0D700.4ds [255 Bytes]
Downloaded 50 times
|
|
|
| Top |
|
|
|
guido
|
Posted: Tue 27. Sep 2016 12:49:19 |
|
Joined: Sun 22. Nov 2015 17:09:02
Posts: 32
|
|
Hi,
I had the same problem with one of my helis after updating to 2.1.
I solved the issue by increasing Spoolup Rampup from 50 to 60µs
I hope that solves your issue too.
brgds
Guido
|
|
| Top |
|
|
|
torro
|
Posted: Tue 27. Sep 2016 14:18:09 |
|
Joined: Mon 20. Jun 2016 20:02:31
Posts: 46
|
|
it works.
i recalibrated the ESC, same problem.
increasing spoolup rampup to 80 was succesfull!
|
|
| Top |
|
|
|
thestructured
|
Posted: Tue 27. Sep 2016 20:30:39 |
|
Joined: Thu 24. Dec 2015 20:13:20
Posts: 157
|
|
I had a similar issue on 2.1 where the governor was not engaging at all until I set the spoolup rate to fast
|
|
| Top |
|
|
|
ZeXx86
|
Posted: Wed 28. Sep 2016 9:23:15 |
|
|
| Site Admin |
Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442
|
|
Thank you for the info.
I am glad it works, although it is little bit strange as the starting procedure is very same with previous firmware.
Increased spoolup works similarly as when you increase Throttle Range - Min.
_________________
Spirit System developer
|
|
| Top |
|
|
 |
Who is online |
 |
Users browsing this forum: Bing [Bot] and 59 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
