| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| DX9 set up no sats no gov https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=1314 |
Page 1 of 2 |
| Author: | bill rob [ Wed 23. Mar 2016 13:10:15 ] |
| Post subject: | DX9 set up no sats no gov |
Has anyone set up with DX9 no sats no gov,I could do with some help! |
|
| Author: | jgiannakas [ Wed 23. Mar 2016 16:36:56 ] |
| Post subject: | Re: DX9 set up no sats no gov |
Yeap I'm running a DX9 with an AR7700 using SRXL connection on my Goblin. To be honest there is no difference to a sat setup that I'm running on my 450L. Shoot your question!! |
|
| Author: | bill rob [ Wed 23. Mar 2016 17:39:14 ] |
| Post subject: | Re: DX9 set up no sats no gov |
Thanks for your reply and offer to help,,Im quite new to DX9 and that's where my problems are,,I just want to set up so I can use rescue on the trainer switch,,so I need DX9 settings to enable this.I take it with pwm wiring there is no need for banks?,,,what should my tx gyro settings be? again thanks for your help Bill |
|
| Author: | jgiannakas [ Wed 23. Mar 2016 17:47:02 ] |
| Post subject: | Re: DX9 set up no sats no gov |
Did you follow my guide here? Spirit Setup Guide http://www.helifreak.com/showthread.php?t=643997 |
|
| Author: | jgiannakas [ Wed 23. Mar 2016 17:47:45 ] |
| Post subject: | Re: DX9 set up no sats no gov |
I would strongly advise using he bind switch. You'll need to move the switch around to the trainer switch but it works MUCH better. It really needs to be a momentary switch that you'll use |
|
| Author: | bill rob [ Wed 23. Mar 2016 17:55:32 ] |
| Post subject: | Re: DX9 set up no sats no gov |
I will move the switch,I followed the set up guide,but its for governor is it not,with bank switching. There is no set up guide for DX9 using pwm wiring,they are all for use of gov. If you could tell me settings for DX9 that would help,also with pwm do I still need banks? |
|
| Author: | jgiannakas [ Wed 23. Mar 2016 18:27:42 ] |
| Post subject: | DX9 set up no sats no gov |
Nope it's not related to governor http://www.helifreak.com/showpost.php?p ... stcount=16 PWM connection or sats or SRXL has nothing to do with the setup on the DX9. |
|
| Author: | bill rob [ Wed 23. Mar 2016 19:51:38 ] |
| Post subject: | Re: DX9 set up no sats no gov |
jgiannakas wrote: Nope it's not related to governor http://www.helifreak.com/showpost.php?p ... stcount=16 PWM connection or sats or SRXL has nothing to do with the setup on the DX9. Great!, I`ll go through that set up then move the switch. Thanks for your help. |
|
| Author: | jgiannakas [ Wed 23. Mar 2016 20:04:43 ] |
| Post subject: | Re: DX9 set up no sats no gov |
No worries. To avoid any confusion all your gyro gain values need to be positive  In the latest firmware I did not need to adjust end points to get my gyro to match the diagnostics screen. But I do recommend following the step on the guide     Mixes are used to enable rescue:    I've also added a voice command on switch activation   This is what the monitor shows before I click rescue  And when I push the button 
|
|
| Author: | bill rob [ Wed 23. Mar 2016 20:38:37 ] |
| Post subject: | Re: DX9 set up no sats no gov |
All good thanks to your good self,rescue working,I`m sure ive seen a video on you tube of moving the switch. Thanks again for your help. Bill |
|
| Page 1 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|