It is currently Sat 23. Nov 2024 4:06:06

All times are UTC + 1 hour





Post new topic Reply to topic  [ 17 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
 Post subject: Re: Rotation rate ?
PostPosted: Mon 10. Oct 2022 20:29:05 
Offline

Joined: Mon 30. Oct 2017 23:47:38
Posts: 162
ZeXx86 wrote:
Hello,

parameters of the servo are great, so it should work well I believe.


Thanks Thomas for the validation.

Mathias,

here is a link to the file, i used a site Thomas used for uploading video files in another support thread : https://files.fm/u/9y4dm57vd

And thanks for the video idea, it was a fun project, had to tape the iphone on my hat ..... They are 2 front 360 flips at 2900RPM, i only brought 1 battery and ran out of juice.

Pierre


Top
 Profile  
 
 Post subject: Re: Rotation rate ?
PostPosted: Tue 11. Oct 2022 18:17:25 
Offline

Joined: Wed 21. Dec 2016 15:13:38
Posts: 566
Location: Germany
Hi Pierre,
thanks for the video !
I don't think the roll rate with elevator is particularly high, it should be faster - I looked in the manual of the Goblin RAW 420 and there are suggestions of pitch range and cyclic range, also for rpm range, I would also set them that way, see the attached excerpt from the manual, thats very important !

greeting
Matthias


Attachments:
Screenshot 2022-10-11_01.jpg
Screenshot 2022-10-11_01.jpg [ 412.79 KiB | Viewed 253 times ]
Top
 Profile  
 
PostPosted: Sat 15. Oct 2022 13:16:42 
Offline

Joined: Mon 30. Oct 2017 23:47:38
Posts: 162
Mattes61 wrote:
Hi Pierre,
thanks for the video !
I don't think the roll rate with elevator is particularly high, it should be faster - I looked in the manual of the Goblin RAW 420 and there are suggestions of pitch range and cyclic range, also for rpm range, I would also set them that way, see the attached excerpt from the manual, thats very important !

greeting
Matthias


Thanks Thomas, Matthias, after a few days of rain I was able to test with a faster RPM of about 3200 and I see a difference in the rate ….

I have a 12,5 degree of pitch but I limited the cyclic to 11, I will try to get 12,5 pitch and 12 cyclic, it probably will help as well.

Can I get the same pitch and cyclic ? Or I should always have a .5 degrees less of cyclic ?

Thanks for the time and the help !

Enjoy the weekend

Pierre


Top
 Profile  
 
 Post subject: Re: Rotation rate ?
PostPosted: Sun 16. Oct 2022 15:50:01 
Offline

Joined: Wed 21. Dec 2016 15:13:38
Posts: 566
Location: Germany
Hi Pierre,
if you will get the max rotation rate you can set it to 12,5 ° cyclic - if you get then an magenta letter you must reduce it until that goes away - I don't think that 0.5° cyclic is more or less realized at all -
What also is important that you have no binding in any position of the cyclic ring by varying the pitch (max. positive/middle/max negative) - you should test it in any case

Regards
Matthias


Top
 Profile  
 
 Post subject: Re: Rotation rate ?
PostPosted: Mon 17. Oct 2022 3:00:40 
Offline

Joined: Mon 30. Oct 2017 23:47:38
Posts: 162
Mattes61 wrote:
Hi Pierre,
if you will get the max rotation rate you can set it to 12,5 ° cyclic - if you get then an magenta letter you must reduce it until that goes away - I don't think that 0.5° cyclic is more or less realized at all -
What also is important that you have no binding in any position of the cyclic ring by varying the pitch (max. positive/middle/max negative) - you should test it in any case

Regards
Matthias
Hi Matthias,

I will go to the max cyclic, 0.5 on a 420 is just a bit of wiggle…. thanks for the confirmation.

In your answer, you write « if you get a magenta letter you must reduce it ».. what is the magenta letter? Is it on the spirit display ?Where do you see this ?

Thanks

Pierre


Top
 Profile  
 
 Post subject: Re: Rotation rate ?
PostPosted: Mon 17. Oct 2022 14:37:45 
Offline

Joined: Wed 21. Dec 2016 15:13:38
Posts: 566
Location: Germany
Hi Pierre,
I mean something like that in the hardcopy:
Attachment:
Screenshot 2022-10-_mag_Letters.jpg
Screenshot 2022-10-_mag_Letters.jpg [ 30.79 KiB | Viewed 184 times ]

If you get maghenta letters or values you must change that, that this disapperars - that's what I meant -

Regards
Matthias


Top
 Profile  
 
 Post subject: Re: Rotation rate ?
PostPosted: Mon 17. Oct 2022 17:14:24 
Offline

Joined: Mon 30. Oct 2017 23:47:38
Posts: 162
Mattes61 wrote:
Hi Pierre,
I mean something like that in the hardcopy:
Attachment:
Screenshot 2022-10-_mag_Letters.jpg

If you get maghenta letters or values you must change that, that this disapperars - that's what I meant -

Regards
Matthias
Ah ok,

Thanks again Matthias, i will stay alert for the magenta on screen, always new things to learn.

Regards

Pierre


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 17 posts ]  Go to page Previous  1, 2

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 57 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .