Spirit System • View topic

It is currently Thu 21. Nov 2024 19:41:59

View unanswered posts | View active topics

Board index » Česky a slovensky » HELI » Nastavení

All times are UTC + 1 hour

Trex 150

Page 1 of 2

[ 19 posts ]

Go to page 1, 2 Next

Print view

Previous topic | Next topic

Author

Message

tomsl

Post subject: Trex 150

Posted: Sat 19. Oct 2019 18:50:27

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

Hi
I converted a Trex 150 to a μSpirit.
I am very happy with it
I can adjust everything with my DS 16
only my tail rotor swings but not always only sometimes.
can someone share settings with me?

Thomas

_________________
official hacker distributor USA
www.hackermotors.us

Top

tomsl

Post subject: Re: Trex 150

Posted: Sun 20. Oct 2019 22:29:36

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

is there anybody who can help ????
Do this or that ....

_________________
official hacker distributor USA
www.hackermotors.us

Top

ZeXx86

Post subject: Re: Trex 150

Posted: Mon 21. Oct 2019 10:01:14

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Yes, but you are asking for somebody with T-Rex 150.
We have no T-Rex 150, but to resolve tail issues you have to change Advanced/Pirouette Consistency parameter.

_________________
Spirit System developer

Top

tomsl

Post subject: Re: Trex 150

Posted: Mon 21. Oct 2019 16:37:52

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

Thank you!
I will test later

_________________
official hacker distributor USA
www.hackermotors.us

Top

tomsl

Post subject: Re: Trex 150

Posted: Mon 21. Oct 2019 16:48:40

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

I'm already at the value of 130
I can not go lower
When I put it up, it starts to swing heavily
Is there still a possibility?

Thank you for your help

_________________
official hacker distributor USA
www.hackermotors.us

Top

ZeXx86

Post subject: Re: Trex 150

Posted: Tue 22. Oct 2019 12:29:52

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

Yes, you can change Rudder Delay. First try to set 0. Then try to set 25. Probably increasing Rudder frequency to a higher can help a lot too.

_________________
Spirit System developer

Top

tomsl

Post subject: Re: Trex 150

Posted: Tue 22. Oct 2019 18:45:52

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

between 0 and 30 no differences

_________________
official hacker distributor USA
www.hackermotors.us

Top

ZeXx86

Post subject: Re: Trex 150

Posted: Wed 23. Oct 2019 8:50:58

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

In this case please decrease Gyro Gain until there are no oscillations and set Advanced/Rudder Revomix to 3-4. This might help a lot.

_________________
Spirit System developer

Top

tomsl

Post subject: Re: Trex 150

Posted: Thu 24. Oct 2019 4:20:48

Joined: Tue 10. Sep 2019 3:02:10
Posts: 33
Location: Whitehall Michigan USA

The Rudder Gain was already at 5% have it set to 0
And Revomix was already at 4 I changed to 3
No difference :shock:

_________________
official hacker distributor USA
www.hackermotors.us

Top

ZeXx86

Post subject: Re: Trex 150

Posted: Fri 25. Oct 2019 11:18:34

Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12442

This is very low value. What will happen if you will set Gyro Gain to 40%?

We can prepare special firmware where Pirouette Consistency can have half effect. Hopefully it will help.

_________________
Spirit System developer

Top

Page 1 of 2

[ 19 posts ]

Go to page 1, 2 Next

Board index » Česky a slovensky » HELI » Nastavení

All times are UTC + 1 hour

Who is online

Users browsing this forum: No registered users and 16 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: