Spirit System
https://www.spirit-system.com/phpBB3/

Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-E
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3375
Page 1 of 1

Author:  pidder [ Tue 02. Jul 2019 14:17:01 ]
Post subject:  Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-E

Hi, my question is regarding the above metioned setup.

I use UniSens-E (under Graupner HOTT as GAM)to detect the used capacity and let the receiver tell me by using a switch.
Now - with the sprirt unit i have to decide whether i will use telemetry port for spirit setup or to use the UniSens-E unit.

My question: Is there any possible wireing to have both functions possible via the telemtry port? :?

regards
Peter

Author:  TomasN [ Tue 02. Jul 2019 16:24:26 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

Yes, you can use Y-cable. But before connecting of both components you have to set UnisensE or Spirit to EAM mode instead of GAM.

Author:  TomasN [ Tue 02. Jul 2019 16:27:43 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit

Author:  pidder [ Thu 04. Jul 2019 19:38:23 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

TomasN wrote:
See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit


this - i will try this - but what about the wires?
The unisons needs the red cable for power-supply. It is recommended that on the SYS-port of the spirit the must not be any voltage!!!

Did you cut the red wire or is it no problem?

Author:  TomasN [ Thu 04. Jul 2019 20:04:31 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.

Attachment:
wiring.png
wiring.png [ 11.38 KiB | Viewed 588 times ]

Author:  pidder [ Fri 05. Jul 2019 7:06:00 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

TomasN wrote:
Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.

Attachment:
wiring.png



Thank you very much - i will try this!!!

Author:  pidder [ Sun 14. Jul 2019 7:59:12 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

TomasN wrote:
Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.

Attachment:
wiring.png



I tried this an it works!!!!! :D :D

Great job thank you very much for your help!

Regards
Peter

Author:  enied [ Fri 28. Feb 2020 11:02:29 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

TomasN wrote:
Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.

Attachment:
wiring.png


Hi TomasN,

does it harm to connect GND ? Currently I have connected it and it works.

Thank you in advance for your feedback.

Best, Eugen

Author:  TomasN [ Fri 28. Feb 2020 12:03:40 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

Connecting also GND is ok . But single signal wire is enough and simplier.

Author:  enied [ Fri 28. Feb 2020 12:30:04 ]
Post subject:  Re: Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-

Thank you !

Page 1 of 1 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/