It is currently Fri 29. Mar 2024 0:14:51

All times are UTC + 1 hour





Post new topic Reply to topic  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Tue 19. Feb 2019 16:05:14 
Offline

Joined: Tue 19. Feb 2019 15:39:37
Posts: 3
Just received my new Spirit Pro from Thomas yesterday and wow, that was fast! I am currently working on getting me XLPower 520 setup. I have the following:

• Spirit Pro
• Hobbywing Platinum 100A V3 ESC
• SPM4649T Serial Telemetry Receiver
• JETI integration cable

I currently have the Sat RX and the SPM4649T RX both bound to my TX. The SPM4649T is connected via the Jeti cable with the Orange wire in the AIL pin and the Red and Brown wires in the RUD port per the manual. The Sat RX is in the side Primary port.

My confusion is when I went to connect my ESC. Per the manual, it says to connect it using the same ports as the SPM4649T. I am sure I am missing something. Not sure if I need another cable, Y harness, etc?

Just trying to figure out what to do with the White/Red/Black connector and the Black/Red connector from the ESC. Not worried about the Orange wire connector since I am planning on using the governor in the Hobbywing ESC (I have the programming box).

Thank you for your help!

Brooks


Top
 Profile  
 
PostPosted: Tue 19. Feb 2019 16:59:46 
Offline

Joined: Tue 19. Feb 2019 15:39:37
Posts: 3
OK, I think I was getting a little confused as I was looking at the page dedicated to the Hobbywing V3/V4 ESCs.

So after going back through the wiring guide in the manual, is this the correct way to connect the ESC:

• Red/Black/White wire (Throttle ESC) - AUX 1
• Red/Black wire (BEC) - AUX 2
• Orange wire - not needed if using the ESC governor

I have a feeling I am going to enjoy the FBL once it is set up, but I kind of miss the flybar setup process. I quit flying helis right when the FBL systems were coming out. Guess I'm getting old. Thank you your help.

Brooks


Top
 Profile  
 
PostPosted: Wed 20. Feb 2019 11:53:19 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12213
Hello,

you are right. Your description is correct according the

The most difficult part would be probably to bind the SPM4649T receiver. Then it should all work.
Do not forget to assin Throttle channel in the Channels in order to activate AUX1 output.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Wed 20. Feb 2019 15:41:27 
Offline

Joined: Tue 19. Feb 2019 15:39:37
Posts: 3
Thank you. And when you say assigning the Throttle channel to AUX1, you are referring to doing this in the Spirit unit, correct?


Top
 Profile  
 
PostPosted: Thu 21. Feb 2019 8:48:16 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12213
Yes, in the General/Channels window you have to assign Throttle channel.

But actually when using SPM4649T it is assigned automatically :) So this is done by Spirit unit for you.

_________________
Spirit System developer


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .