Hi Adrian,
please try this firmware:
http://spirit-system.com/dl/fw/spirit-fw-2.4.5.4df
Hopefully it will help
Thank you very much!
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| FrSky / OpenTx Signal loss during LUA configuration https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=2207 |
Page 2 of 2 |
| Author: | Adrian [ Fri 15. Sep 2017 10:16:59 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
Hi BT Thanks for testing. Have you forced a log record before doing the test by switching off the TX while RX is armed? I have found it's hard to get a signal loss record if there is no log stored, but once there is a stored log it happens more frequent. If you still don't see issues, where does our setup differ? X6R(1) FW LBT_151118 X6R(2) FW EU_170210 Spirit 2.4.2 and 2.4.4 TX Horus X12S with OpenTX 2.2.0 running on EU FW Failsafe configured as [Custom] in Horus for RX. many thanks, Adrian |
|
| Author: | ZeXx86 [ Fri 15. Sep 2017 11:48:09 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
Hi Adrian, I have prepared firmware with small modification. There the Log will be never cleared even after viewing the events. It could help us little bit in understanding where the problem is: http://spirit-system.com/dl/fw/spirit-fw-2.4.25.4df Hopefully it will not happen with this firmware. If it will, then it is possible that the problem is in the receiver firmware. |
|
| Author: | Adrian [ Fri 15. Sep 2017 20:30:21 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
Hi Tomas With this FW 2.4.25 there is no signal lost with LogView.lua But I can get signal Lost doing Bank switch in basic.lua As you said, Logview.lua does not clear the log. Afterwards I did open Log with WinPC and USB Interface. In the very same moment where the Warning popped up about previous Log, Spirit went into FailSafe. But it's not happening always. Once it works, its also clearing the log. regards, Adrian |
|
| Author: | ZeXx86 [ Sun 17. Sep 2017 22:08:45 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
Hi Adrian, thank you very much for the message! It was really helpfull. Maybe we will find solution tommorow. |
|
| Author: | ZeXx86 [ Wed 20. Sep 2017 7:39:47 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
Hi Adrian, please try this firmware: http://spirit-system.com/dl/fw/spirit-fw-2.4.5.4df Hopefully it will help Thank you very much!
|
|
| Author: | Adrian [ Wed 20. Sep 2017 19:32:21 ] |
| Post subject: | Re: FrSky / OpenTx Signal loss during LUA configuration |
I got the feeling it got better, but I do still get the Failsafe. On every 3-4 Bankswitches as well as on LogView.lua An other observation, doing Pitch movement during Bankswitch in LUA the servos do sometimes move jerky and even system goes into Failsafe. |
|
| Page 2 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|