It is currently Thu 28. Mar 2024 21:11:20

All times are UTC + 1 hour





Post new topic Reply to topic  [ 2 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Wed 23. Nov 2016 22:03:12 
Offline

Joined: Thu 01. Oct 2015 15:13:29
Posts: 162
I installed a Spirit Pro on a Synergy 766 helicopter. I am trying to optimize the Spirit gain values. This is my mechanical and electronic setup:

Helicopter: Synergy 766 airframe
Total flying weight with batteries: 14.48 lbs. (6,570g)
Blades: Rail 806mm mains, and Rail 116mm tail
Head to tail ratio: 1:5.1
Kontronik governed head speeds: 80% = 1,750rpm, 74% = 1,600rpm, 69% = 1,500rpm
Cyclic servos: MKS HBL599 http://www.mksservosusa.com/product.php?productid=196&cat=27&page=1
Tail servo: MKS HBL880 http://www.mksservosusa.com/product.php?productid=131&cat=24&page=1
Kontronik BEC set to 7.9V
Collective Pitch range set to "125" = 12.6°/-12.5°
Cyclic range set to "130"
Transmitter: Jeti DS-16
Receiver: Jeti REX7



I would like to learn the optimal numbers to enter into the Spirit:
1) Cyclic Gain
2) Rudder Gain (In transmitter)
3) Rudder Common Gain
4) Elevator Filter
5) Cyclic Feed Forward
6) Rudder Delay
7) Rudder Dynamic
8) Pirouette Consistency
9) Stick Deadband


Attachments:
Syn 806 Spirit Pro Setting 2016-11-22.4ds [255 Bytes]
Downloaded 107 times
Top
 Profile  
 
PostPosted: Thu 24. Nov 2016 8:31:09 
Online
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12213
Hello,

here are the values that should work well

1) Cyclic Gain: 60-70%, usually 64% is good on nearly any heli.
2) Rudder Gain (In transmitter): must be determined in the flight (increase until fast forward flight or pitch pump oscillation will occur)
3) Rudder Common Gain: without a change
4) Elevator Filter: 3-4 (if you can observe bounce back on the elevator during hard maneuvers, increase)
5) Cyclic Feed Forward: this is rather preference matter, usually 4-8
6) Rudder Delay: without a change
7) Rudder Dynamic: preference, default is working usually well.
8) Pirouette Consistency: 180 - 195 (if rudder is not holding even that there are oscillations due to high gyro gain, increase the value)
9) Stick Deadband: 4 - 15 will work well. With lower value, deadband will be smaller.

If you want to make collective pitch exactly equal on both directions, you can use Servo Travel Correction in the Servo tab, where by decreasing value for positive col. for all 3 servos will do the job.

_________________
Spirit System developer


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: ZeXx86 and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .